Glossary

Every term the site's ⓘ tooltips define, in one list: the term as it is labelled beside the control, the tooltip's own sentence, and the docs page that explains it at length. The list is the help registry itself, sorted by label, so a term added to a page appears here on the same day.

TermMeaningWhere
−x % CDHow much lower the RMS drag coefficient is than the start's, over the operating points both sections reach. Green is an improvement; grey means the solver could not beat the start within your constraints and handed it back.Optimize
3D previewThe wing lofted live from the controls, both halves. Seven camera views on keys 1–7, Ortho or Persp on O, the ground grid on G, Expand on E. Drag to orbit, scroll to zoom, right-drag to pan.Wing designer
3D WingOpens the wing designer with the first visible section as the root, and as the tip until you pick another. Library sections only: a custom, uploaded or saved one has no library name, so the designer opens with its default section.Compare
Airfoil geometryEvery visible section at unit chord, outline and mean line, in the colour its curve has on the chart. The table gives maximum thickness and camber (% chord) and where each peaks (% x/c from the leading edge).Compare
Alpha(deg)The angle of attack at which the section makes the required Cl at that Re, read off the stored lift curve. A wide spread between rows means the wing must work across a wide angle range.Mission
Altitude(m or ft)Only for "Air (custom altitude)": density falls as 1.225·e^(−h/8500) with h in metres, an isothermal-atmosphere fit; viscosity stays at sea-level air. Higher means a lower Re and a higher lift coefficient.Mission
Analyze and Compare, Use on wing, SaveEach takes the section with the scalars applied, under the name in the box. Compare runs its polars; Root or Tip opens the wing designer with it in that slot; Save puts it in your account, from where it can be reopened here.Kulfan canvas
Analyze WingSends the wing as 20 stations sampled from the drawn splines, root and tip sections blended between them. Sign in first. A free monthly allowance of wing-analysis credits is spent before your balance; the counter says what is left.Wing analysis
Angle of attack(deg)Angles of attack for the run: from Start to Stop every Step degrees, -10° to 15° in 1° steps by default. Go past the stall if you want the peak; a finer step draws a smoother curve.Compare
Apply to Wing →Carries the operating points, fluid, Ncrit, filters, mass and area to the wing designer, which takes its speed, fluid and lift coefficient from the heaviest-weighted point. No search is run.Mission
ARAspect ratio of the generated stabiliser, span² over area. The usual band for a tail is 3–5: responsive without stalling before the wing.Trim
ARAspect ratio, span squared over area, read-only. Nothing here uses it: the selector scores sections. It sets how much induced drag the finite wing adds, which the wing pages model.Mission
Area(cm² or m²)Planform area of the generated stabiliser, both halves. With the aspect ratio it fixes the span, b = √(AR · S), and with the taper the chords.Trim
Arm(mm or m)Main-wing MAC quarter chord to this surface's MAC quarter chord: the tail-volume card's l_h. Typing here moves x so the arm comes out as typed.Trim
Aspect ratioFull span squared over planform area. Higher means less induced drag for the same lift and a heavier root bending load; a glider is 20 and up, a freeride foil about 9.Wing designer
Batch exportEvery visible section, up to 5, one file each. DAT: 151 Selig-order points at unit chord. DXF: the section at a 1,000 mm chord, for CAD. Hidden sections are left out.Compare
Bernstein WeightsEach weight scales one Bernstein bump, centred at i/n along the chord; the first sets the nose radius, the last the tail angle. Upper weights are positive, lower negative. + and − add or drop a weight, down to 2.Kulfan canvas
Best L/DThe highest lift-to-drag ratio in the sweep, and the lift coefficient and angle it occurs at. Flying near that Cl gives the best glide.Foil page
Bias(% chord)Where along the tip chord the rounded cap reaches furthest out, as a percentage from the leading edge, 5 to 95. Tangency to the edges limits the range; the readout says where the peak actually landed.Wing designer
Boattail Angle(deg)The half-angle the two surfaces close at. Dragging it writes the last upper weight and minus that value into the last lower weight, so the trailing edge becomes symmetric about the chord line at that angle.Kulfan canvas
Camber(% chord)Maximum camber as a percentage of chord: how far the mean line bows away from the chord line. More camber shifts the lift curve up and moves the drag bucket toward higher lift.Foil page
Camber(% chord)The largest distance of the mean line from the chord line, as a percentage of chord. Negative when the mean line bows downward.Kulfan canvas
Camber(% chord)Bounds the camber, as a percentage of chord: a positive minimum is a floor on the peak, a negative minimum on the dip. A band within 0.25 % of zero asks for a symmetric section. Opens off, at -2 to 6.Optimize
Camber(% chord)Maximum camber of the optimized section, as a percentage of chord. More camber than the start is the usual way the solver reaches a high-lift point cheaply.Optimize
Camber(% chord)Keep only sections whose maximum camber, as a percentage of chord, lies between Min and Max. The magnitude is tested, so a reflexed or inverted section counts by its size. Applied before scoring.Mission
Camber(% chord)Keeps sections whose maximum camber, as a percentage of chord, lies between the two values; a negative value is camber below the chord line. Opens at -10 to 10.Search
Camber ScalarMultiplies the camber half of every weight pair, (upper + lower)/2. 1 is the section as loaded, 0 makes it symmetric, negative inverts it. Loading a section sets it to 1; the page opens at 0.Kulfan canvas
Card figures(% chord)Thickness and camber as a percentage of chord, each with @: where along the chord it peaks, as a percentage from the leading edge. Measured from the drawn CST geometry, the same curve the DAT and DXF carry.Search
CdDrag coefficient of the section alone (profile drag). A finite wing adds induced drag on top of it.Foil page
CDWhole-wing drag coefficient at the same point: induced drag from the spanwise loading plus each section's profile drag from NeuralFoil at its local Reynolds number.Wing analysis
CD·A(m²)A board, pod or fuselage as a drag area: drag = q · CD·A at the point given. It adds to the thrust and a moment through its height, not to the pitch stiffness, so the static margin ignores it.Trim
CG(× MAC)Centre of gravity as a fraction of the wing MAC, measured aft of the MAC leading edge. 0.25 is the wing's own aerodynamic centre; the static margin is how far the neutral point sits behind this.Wing designer
CG x(mm or m)Centre of gravity aft of the main wing's root leading edge. Moments are taken about it; the caption below converts it to a percentage of the wing MAC.Trim
CG z(mm or m)Height of the CG above the wing, up positive. First order on a hydrofoil: the lift's forward component at angle of attack, times this height, is a pitching moment that grows at low speed.Trim
ChecksA requirements re-check on the run, pass / warn / fail / n/a: where it stalls first, the tip Reynolds number against the library's floor, the cruise pitching moment. n/a means not measured here, not failed.Wing analysis
Chord(mm)The chord the DXF is drawn at, in millimetres, so it lands in CAD at the size of the rib or the mould. It does not affect the DAT, which is always at unit chord. Opens at 100.Kulfan canvas
Chord(mm or m)Chord of the mast or strut. With the speed and the fluid it sets the section's own Reynolds number, which fixes its drag coefficient.Trim
ClLift coefficient: lift divided by dynamic pressure and area. Depends on angle of attack, camber and Reynolds number, not on size.Foil page
CLThe lift coefficient the section must reach at this point, -1 to 2.5. A target the starting section cannot reach below its stall is refused before any solve, without charge.Optimize
CLWhole-wing lift coefficient at the starred best-L/D point: lift over dynamic pressure and S_ref. In constant-lift mode it is the CL the load demands at that speed.Wing analysis
Class Function N1The exponent on x in C(x) = x^N1·(1−x)^N2: 0.5 gives a round nose, 1 a pointed one. Every library section, NeuralFoil and the optimizer use 0.5; other values draw but cannot be analysed.Kulfan canvas
Class Function N2The exponent on (1−x): 1 closes the tail to a sharp edge, smaller values blunt it, 0.5 rounds it like an ellipse. Library sections and NeuralFoil use 1.Kulfan canvas
ClmaxPre-stall lift peak at the main operating Re. Higher is better: scaled 0–1 across the matched candidates and multiplied by this weight.Mission
CmPitching-moment coefficient about the quarter chord. Negative is nose-down; a cambered section has a negative Cm that barely changes with angle until the stall.Foil page
CMPitching-moment coefficient of the wing at the starred point, nose-up positive. What a stabiliser has to balance; Trim does that sum with the CG where you put it.Wing analysis
CM (pitching moment)Keeps the quarter-chord pitching moment at every operating point inside the range. Camber buys drag with nose-down moment; a floor here is how a flying wing or a stabiliser stops that trade. Opens off, at -0.15 to 0.05.Optimize
Constraint SlackHow far inside each bound the returned section sits, in the bound's own units: positive is satisfied, zero is on the bound, a small negative is an overshoot within tolerance that Solver notes will name.Optimize
ConvergenceThe objective, the weighted sum of CD over your operating points, at each IPOPT iteration of the final solve. A fast drop then a flat tail is normal; a jagged tail means a constraint became active part-way.Optimize
Copy tableCopies the geometry table as tab-separated text (name, max thickness, its location, max camber, its location), ready to paste into a spreadsheet. Hidden sections are included.Compare
CraftThree starting rigs: hydrofoil (the rider a metre up on a mast), RC and full-scale. A template seeds every input; its stabiliser is a plain generated panel meant to be replaced by a saved design. Switching resets the craft.Trim
DAT and DXFDAT: 151 Selig-order points at unit chord, for XFLR5, XFoil or OpenVSP. DXF: the section at a 1,000 mm chord, for CAD. Each card has its own pair; the floating pair downloads every selected card, one file each.Search
Decision matrixWhere this section stood on each criterion among the candidates that matched: a full bar is the best of the set, empty the worst, ×w the weight. With non-default weights the matrix score is 100 × (1 − weighted cost / Σ weights).Mission
Dihedral(deg)Angle of the tip above the root, -20 to 30°; negative is anhedral, the tips below the root. Sets the end of the front-view curve; points on that curve shape the path between.Wing designer
DownloadDXF: the section at a 1,000 mm chord, for CAD. DAT: 151 Selig-order points at unit chord, for XFLR5, XFoil or OpenVSP. CSV: the plotted polars, columns Re, Ncrit, alpha, CL, CD, CM.Foil page
Download CSVDownloads the run as wing_polar.csv, columns alpha, CL, CD, CM, L_over_D, one row per point. A constant-lift run writes the trimmed α of each speed but no speed column; read the speeds off the α-vs-V chart.Wing analysis
DragCD at each operating CL, weighted by the operating points — the only criterion the default ranking uses. Lower is better: scaled 0–1 across the matched candidates and multiplied by this weight.Mission
DurationWall-clock time inside the solver, search and polish included. Most of it is NeuralFoil: a larger model is slower per call, more operating points mean more calls per iteration.Optimize
Efficiency ratioClmax divided by minimum CD at the main operating Re. Higher is better: scaled 0–1 across the matched candidates and multiplied by this weight.Mission
Estimate termsThe four factors the neutral point is built from: area ratio S_h/S, arm in chords l_h/MAC, the tail's lift slope over the wing's, and 1 − dε/dα, how much of the wing's downwash the tail sits in.Wing designer
Export ToolsDXF: the section at the chord in mm, for CAD. DAT: unit chord, Selig order, for XFoil, XFLR5 or OpenVSP. Both carry the scalars and the trailing-edge gap set by the TE Thickness slider; the DAT carries the name.Kulfan canvas
Find →Opens Mission with this slot's Reynolds number and the design CL already filled in, so the selector ranks sections for exactly this station. Its results offer "Apply to root" or "Apply to tip".Wing designer
First stallWhere the wing stalls first, as a fraction of the half-span from the root, with a verdict. Root-first is wanted; tip-first means washout or a higher-lift tip section; mid is inboard of 70% but not at the root.Wing analysis
FluidAir, salt water or fresh water: density for the dynamic pressure, viscosity for the Reynolds number. ρ = 1025 kg/m³ salt, 999.1 fresh, 1.225 air; the same constants the Design tab uses.Wing analysis
FluidAir, salt water or fresh water: density for the dynamic pressure, viscosity for each section's Reynolds number, the mast's included.Trim
Fluid typeDensity and viscosity for Re and dynamic pressure: air at sea level 1.225 kg/m³, fresh water 999.1, salt water 1025.9 kg/m³ (ITTC values at 15 °C). The ρ and μ in use are printed beside the selector.Mission
FormatSTEP is the exact lofted solid for CAD: shell it, split it, cut moulds from it. STL is the same solid as a triangle mesh for slicers and mesh tools. Both are in millimetres and hold both halves.Wing designer
free · solved / fixedMarks the one surface whose incidence the solve sets; the others keep theirs. The reference wing is never free. Pick the stabiliser.Trim
Free runs3 live runs per 30 days without an account. With a free account the live run is unlimited, up to 120 an hour.Foil page
Freeze TE thicknessHolds the trailing-edge gap at the starting section's value instead of letting the solver choose it. Recommended: a free gap is one more way to shave drag that the shop has to undo.Optimize
Full span(mm)Twice the half-span: the whole wing, tip to tip. Every length you type is for one half; the derived figures and the export are for both.Wing designer
Generate 3D wingBuilds the solid in CAD on the server and downloads it, usually in under 20 s; it stops at 90 s and says why. Needs a sign-in and a root section. The file is the same loft the viewer shows.Wing designer
Geometry PresetSets N1 and N2 for a named class of body and overwrites every weight to ±0.15, with the leading-edge weight, TE thickness and scalars reset. It is a fresh start, not an edit of the loaded section.Kulfan canvas
Grid densityHow many cards per row, 1 to 4. A phone opens at 1. It changes the layout and nothing else.Search
h_n(c̄)Stick-fixed neutral point of wing plus tail, as a fraction of c̄ aft of the MAC leading edge, from the tail volume and a momentum-theory downwash. No z-arm, no fuselage or mast.Trim
Half-span(mm)Centreline to tip, for one half; the wing is mirrored about the root. 100 to 20,000 mm. Interior points keep their position in mm, so lengthen the span and they stay where they were.Wing designer
Incidence(deg)Setting angle of the surface, nose-up positive. On the free surface it is only the starting value: the solve replaces it.Trim
IPOPT · NeuralFoilA gradient solve from your start, then a population search over NeuralFoil refined by IPOPT; the better of the two is returned. Gradients are exact, by CasADi automatic differentiation through NeuralFoil itself.Optimize
IPOPT iterationsIterations of the IPOPT solve that produced the answer. IPOPT stops at a point where no feasible direction lowers the drag, so a small count is usually a clean convergence, not a solver that gave up.Optimize
KindPerformance: scored, its drag at the required CL goes into the ranking. Constraint: checked, the section must reach the point's load with a stall margin or it is excluded and named; it adds nothing to the score.Mission
Kulfan parametersThe CST (Kulfan) numbers that draw this section: class exponents n1 and n2, a trailing-edge thickness, a leading-edge weight, and the Bernstein weights of each surface. Paste them into the Kulfan canvas to edit the shape.Foil page
Kulfan ParametersThe parameters as drawn, as JSON: N1, N2, TE thickness, the leading-edge weight and the raw weights. The two scalars are not folded in; exports, Compare, the wing and Save apply them first.Kulfan canvas
L/D maxThe highest lift-to-drag ratio in the run, and the angle (or in constant-lift mode the speed) it occurs at. Ranked by magnitude within the lift sign the run is about, so a downforce surface reads correctly.Wing analysis
L/D placementDegrees between the best-L/D angle and the main operating angle. Lower is better: scaled 0–1 across the matched candidates and multiplied by this weight.Mission
LE and TE pointsAdd a point to the leading or trailing edge and drag it: the edge becomes a smooth curve through every point. Diamonds at root and tip set the end tangents; the root one is locked level so the two halves meet without a kink.Wing designer
Leading Edge Mod WeightAdds the same bump, w·x·(1−x)^(n+1.5), to both surfaces, so it bends the mean line just behind the nose without changing the thickness there. Positive raises both surfaces behind the nose; symmetry forces it to 0.Kulfan canvas
Length(mm or m)Immersed length of the mast or strut. Drag is q · chord · length · Cd of a symmetric section at its own Re; no lift and no side force.Trim
Load(N)The load a constraint point must carry, in newtons; the kgf equivalent is shown beneath. Negative is a downward load, checked against the negative stall instead of Clmax. Blank falls back to Mass × g.Mission
Load .dat fileFits 8 weights per surface plus the leading-edge weight to a Selig-order .dat by least squares, at the current N1 and N2. The chord is normalised first and the trailing-edge gap is read from the file's end points.Kulfan canvas
Load foil from databaseLoads a library section's stored CST parameters, exactly as its page draws them, and resets both scalars to 1. Type a name; the list offers every section in the library.Kulfan canvas
Load performance dataFetches the stored NeuralFoil sweep for this section: 14 Reynolds numbers at Ncrit 1, 4, 9, α -20° to 25° in 0.5° steps. It was run once and stored; nothing is computed now.Foil page
Loft sectionsHow many stations the exporter lofts through between root and tip, 10 to 80, default 30. More follows a curved edge or a twist profile more closely and takes longer to build.Wing designer
MAC(mm)Mean chord, area over span, in mm: the chord each operating point's Reynolds number is computed on. A tapered wing's mean aerodynamic chord differs a little; the wing designer works that one out.Mission
MAC(mm)Mean aerodynamic chord, ∫c² dy / S over the half-wing. The reference length for Reynolds number at the wing level, for pitching moment and for the static margin.Wing designer
MAC spanwise(mm)How far out from the centreline the mean aerodynamic chord sits. Where the half-wing's lift acts, near enough, so it is the arm the root bending moment works on.Wing designer
MachFlight Mach number, 0 to 0.9. 0 is incompressible, right for anything in water and most model aircraft; a value above about 0.3 adds a compressibility correction to the lift and drag at every point.Optimize
MachFreestream Mach number for the run, 0 to 0.9. 0 is incompressible, right for water and for air below about Mach 0.3. Library sections keep their stored polars, run at Mach 0, whatever is set here.Compare
Mass(kg)Everything the lift must carry: craft, rider, payload. The solve sets the lift of all surfaces together equal to mass × g.Trim
Mass(kg or lb)The load this one surface carries, as a mass: lift = m × 9.81 m/s². For a main wing that is the whole craft. A stabiliser enters its trim load on a Constraint point in newtons instead, and can leave this blank.Mission
Match CdThe section's drag coefficient at that Cl and Re, interpolated on the pre-stall branch of the stored polar. The one number the default ranking is built from.Mission
Match ClThe lift coefficient the point requires, L / (½ρV²·S), which the section's polar was read at. A section that cannot reach it before stall at that Re is not in the list.Mission
Match CmPitching-moment coefficient about the quarter chord at the matched angle; negative is nose-down. The value the Cm filter tests, and what the pitching-moment criterion averages.Mission
Match ReThe Reynolds number the row was read at: your exact value, interpolated between the two stored sweeps around it, or the nearest stored sweep when the point lies outside the stored range.Mission
Max camber loc(% chord)Where along the chord the camber peaks, as a percentage from the leading edge.Foil page
Max Camber Loc(% chord)Where along the chord the camber peaks, as a percentage from the leading edge.Kulfan canvas
Max camber loc(% chord)Keeps sections whose camber peaks between the two positions, as a percentage of chord from the leading edge. Opens at 1 to 99.Search
Max ClThe lift coefficient at the stall peak: the first maximum of the lift curve, not the largest value in the sweep, which runs far enough past stall for lift to climb again.Foil page
Max itersThe most IPOPT iterations one solve may take, 20 to 400. A run that stops here with every constraint met is still returned, with a note saying more iterations may lower the drag further.Optimize
Max t/c loc(% chord)Where along the chord the section is thickest, as a percentage from the leading edge. Further aft usually means a longer laminar run and a narrower low-drag range.Foil page
Max t/c Loc(% chord)Where along the chord the section is thickest, as a percentage from the leading edge.Kulfan canvas
Max t/c loc(% chord)Keeps sections whose thickness peaks between the two positions, as a percentage of chord from the leading edge. Opens at 1 to 99. Further aft usually means a longer laminar run.Search
MethodAeroBuildup walks NeuralFoil section polars across the span with finite-span corrections: 10–20 s, 1 credit, stall included. VLM solves a vortex lattice: 60–240 s, 2–3 credits, attached flow only.Wing analysis
Min CdThe lowest drag coefficient in the sweep: the bottom of the drag bucket, where cruise and speed runs live.Foil page
ModelNeuralFoil network for the run: medium, large, xlarge. Larger is a little more accurate and slower. The stored library polars were run with large and are not re-run, so this changes nothing for them.Compare
My foilsSections saved to your account from Compare or the Kulfan canvas. Click one to add it (💾) or take it off. Polars from a run are saved with it, so the same Reynolds numbers and Ncrit again cost no run.Compare
NACA 4-digitGenerates the section from the NACA formulas (camber, its position, thickness) and fits the weights to it at N1 0.5 and N2 1. The fit is close, not exact: the NACA thickness form is not a Bernstein sum.Kulfan canvas
NACA 5-digitThe same fit for a 5-digit code. Normal series only: a reflexed code (third digit 1) is drawn with the normal camber line and says so.Kulfan canvas
NameThe first line of the DAT and the file name of both exports. It mirrors the NAME box at the top of the page, which is why the arrow points there; a loaded section fills it in.Kulfan canvas
NcritHow readily the boundary layer turns turbulent, as the e^N transition exponent. 9 is the clean-tunnel standard and the default here; 4 and 1 stand for a rougher surface or more turbulent flow, and mainly move the drag bucket.Foil page
NeuralFoil modelWhich NeuralFoil network evaluates every candidate. large is the default and what the stored polars use; smaller ones answer faster and less accurately, xlarge slower. The result is only as good as the model that scored it.Optimize
Neutral pointStick-fixed neutral point of wing plus tail, as a fraction of MAC and in mm: the CG position at which the rig would be neutrally stable. No fuselage; one moves it forward by about 0.05–0.10 MAC.Wing designer
NF evalsHow many NeuralFoil evaluations the run made, summed over the operating points, the population search and every IPOPT iteration and line-search step.Optimize
One speed / SweepOne speed solves a single trim point (2 credits). Sweep solves a row at each speed from the low to the high value, the trim-vs-speed curve (3 credits, up to 20 rows).Trim
Open in GeneratorOpens the Kulfan canvas, but does not carry the optimized shape with it. To edit the result there, Save it to your account and open it from the dashboard, or export the CST JSON and load that.Optimize
Operating conditionsSpeed, fluid and design lift coefficient. They set the Re ≈ beside each section and what Find → and Optimize → ask for. Set them on Mission, or load a reference design, which carries its own.Wing designer
Operating PointsEach row is a condition the section must meet exactly: at that Reynolds number it is flown to that lift coefficient, and the drag there counts with that weight. The solver minimises the weighted sum of those drags. Up to 20 rows.Optimize
Optimize →Carries the operating points, Ncrit and the filters to Optimize, so a shape can be optimised at exactly these Re and CL. No search is run first; Design Custom on the results page also starts from the top section.Mission
Optimize →Opens Optimize starting from this slot's section at its Reynolds number and CL. The optimized shape comes back to the same slot. Needs a section in the slot first.Wing designer
Per pageCards per page: 12, 24, 48, 96, 200. Opens at 12. The count after Showing is the whole filtered list; Prev and Next page through it.Search
Performance (matched polars)The stored Cl–Cd polars at the Reynolds buckets around each operating point, at the chosen Ncrit, with a star at each point's matched Cl and Cd. A star near the bottom of a curve is a point flown in the drag bucket.Mission
Pitch moment (Cm)Keep only sections whose pitching moment about the quarter chord, at each performance point's matched angle, lies between Min and Max. Checked at the points you fly, not the polar's extremes; not applied at constraint points.Mission
Pitching momentMean |Cm| at the operating points; a large moment becomes trim drag. Lower is better: scaled 0–1 across the matched candidates and multiplied by this weight.Mission
Planform area(m²)Both halves, integrated from the drawn leading and trailing edges at 40 stations, not from a trapezoid, so a curved outline counts. It is the S_ref the analysis reports.Wing designer
Plot typeWhich pair the chart draws: lift against drag (the polar), or lift, drag or pitching moment against angle of attack. One curve per ticked Reynolds number, at the selected Ncrit.Foil page
PointsLines in the DAT in total, both surfaces, the leading edge written once (10 to 1000). 150 gives 76 per surface, spaced closer at the nose and tail. The DXF has its own sampling.Kulfan canvas
PolarA section's lift, drag and pitching-moment coefficients across angle of attack at one Reynolds number and Ncrit. The Cl-vs-Cd curve is the polar proper.Foil page
PolarsFour charts of the run. α sweep: CL, L/D and CM against α, and the drag polar. Constant lift: trim α, CD, L/D and the required CL against speed, in the selected unit; an × marks a speed the wing cannot carry the load at.Wing analysis
PresetDrag only ranks by the matched drag alone, the default. Textbook is Gudmundsson's worked example: Drag 3, Clmax 2, Stall gentleness 3, Pitching moment 1, Efficiency ratio 1, L/D placement 1. Any other mix shows as custom.Mission
PresetsLoad fills every field from a saved set: surface, fluid, points, filters and weights. Save stores the form under a name. Presets live in this browser and, when signed in, in your account.Mission
ReThe Reynolds number at this point, 10,000 to 50,000,000. Each point keeps its own; a take-off point at low Re and a cruise point at high Re are solved together. Mission fills these in from speed and chord.Optimize
Re ≈The Reynolds number at this section, from its own chord, the operating speed and the fluid: Re = ρVc/μ. The tip, with a shorter chord, flies at a lower Re than the root; read each section's polars there.Wing designer
Reach(% tip chord)How far the cap extends past the tip station, as a percentage of half the tip chord: at 100 it reaches half a tip chord outboard; at 0 the tip is cut flat. The export carries the same cap.Wing designer
Reference designs15 complete wings at real sizes, from a surf foil to a bizjet. Loading one replaces everything: planform, sections, tip cap, export settings and the speed, fluid, CL and mass it was sized for.Wing designer
Required thrust(N)The thrust that closes the x-balance, T = total drag: every surface's induced and profile drag plus the masts, pods and drag areas.Trim
Reset to DAE-11Puts back the section the page opens with, the DAE-11, and turns symmetry off. Open the page with ?foil=<name> to start from any library section instead.Kulfan canvas
ResidualsHow closely the solve closed: lift minus weight in N and the moment about the CG in N·m, then the solver evaluations it took and the sidecar's time.Trim
Reynolds numberRe = V·c/ν: speed times chord over the fluid's kinematic viscosity. The one number that says how big and fast a wing is to the fluid; every polar depends on it.Foil page
Reynolds numbersWhich of the stored Reynolds numbers are drawn; each tick is one curve. Tick the ones around your own operating point. For the exact value, run it below the chart.Foil page
Reynolds numbersComma-separated Reynolds numbers for the run (1e5, 5e5, 1e6, 2e6 by default; 5e5 or 500000 both work). One polar per value per analysed section. Library sections are not run: their stored values are ticked in the chart instead.Compare
Reynolds numbers drawnWhich Reynolds numbers are drawn, one curve each: the stored values of the library sections at the chart's Ncrit, plus any a run added. Opens with the highest ticked; the lowest ticked is solid, the rest dashed.Compare
RMS CD (opt)The same figure for the optimized section, re-evaluated after the solve on the geometry you are given, not read from the solver's last iterate. The headline percentage is (start − opt) / start.Optimize
RMS CD (start)Root-mean-square of the drag coefficient at each operating point, for the starting section. One number for the whole envelope, unweighted; the solver minimises the weighted sum, this reports the result.Optimize
RootThe section at the centreline. Type to search the library. With no tip section it is the whole wing; the viewer, the analysis and the export all draw from the same CST parameters.Wing designer
Root chord(mm)Leading edge to trailing edge at the centreline, 10 to 5,000 mm. Sets the root section's Reynolds number and, with the tip chord, the taper ratio.Wing designer
Run it at your Reynolds numberType the Reynolds number your chord and speed give (340000, 340k or 3.4e5; 10,000 to 100,000,000). NeuralFoil computes that polar now at the chart's Ncrit and draws it with the stored curves. A stored value costs no run.Foil page
Run NeuralFoilComputes polars for the visible custom, uploaded and saved sections at the options above and draws them with the library sections' stored polars, which are not re-run. The count on the button leaves saved sections out; they are analysed.Compare
Runs left this monthFree optimizations remaining in the month, out of the monthly allowance. After it, a run spends credits. A run that returns no airfoil is not counted and not charged.Optimize
S_ref · b · AR · c_refWhat the coefficients are referenced to: planform area, span, aspect ratio and reference chord, all projected (the wing seen from above) so they agree with the Design tab's derived figures.Wing analysis
Save analysisSaves the run to your Dashboard under Analyses, and with the box ticked the wing it was run on as a design, so you can reopen the geometry and keep iterating. A connected agent can read both.Wing analysis
ScoreMatch Cd × 1000, the per-point term the drag sum is built from, scaled so it reads at a glance. Lower is better. Multiply by the point's weight share and sum to get the drag term behind Suitability.Mission
Search DatabaseRuns the selector: every library section with a stored polar at this Ncrit, filtered by thickness and camber, matched at each point's Re and CL on the pre-stall branch, checked at the constraints, ranked by the weights.Mission
Search nameMatches the library name and the display name, fuzzily, so a typo or a missing space still finds it. An exact name comes first, then names that start with what you typed. Typing switches Sort to Relevance.Search
SectionThe symmetric library section the generated stabiliser is built from. Thinner means less drag and an earlier stall; the solve reads its polar at the tail's own Reynolds number.Trim
Select to compareThe box on a card selects it, up to 5 at once; the selection is kept in this browser. Compare opens the selected sections on one chart, and the floating DAT and DXF buttons download them all.Search
Selected foilsA bare name is a library section with stored polars; ✦ came from the Kulfan canvas, ↑ from an uploaded .dat, 💾 from your account, and those three need Run NeuralFoil. The eye hides one from the chart and the exports; × removes it.Compare
Set constant TE thicknessConverts a gap in mm at a chord in mm into the TE Thickness slider: the result is rounded to 0.01 % of chord and capped at the slider's 2 %. 0.5 mm on a 100 mm chord is 0.5 %.Kulfan canvas
ShadingSolid shows the surface as a painted composite would read. Solid+wire adds the station rings and the leading, trailing and quarter-chord lines over it. Wires shows only those, so the loft is visible through the wing.Wing designer
Shape Function PlotDraws the two shape functions under the section: the weighted Bernstein sum for each surface, before the class function shapes it. A weight moves a bump in this plot; the section follows.Kulfan canvas
Simulation conditionsThe settings the stored sweep was run at: Mach 0 (incompressible), the Ncrit shown, and NeuralFoil's large network. Fixed for stored data; a live run uses the same Mach and model.Foil page
SM(c̄)h_n − h_cg as a fraction of c̄; positive is statically stable. The solve on the right reports the same quantity with the downwash solved rather than estimated, in mm as well as c̄.Trim
SolveRuns the lifting-line solve on both surfaces together. 2 credits a trim point, 3 a sweep, from your balance: trim has no free allowance. Nothing is charged until the solver answers, and a sweep refused on every row is not charged.Trim
Solve forThe solve sets the free surface's incidence with the CG fixed. The inverse, where do I stand with the stabiliser fixed, is in the connector tool (analyze_trim, free: cg) and comes to this page later.Trim
Sort byOrders the cards by Name, Thickness or Camber, or by Relevance to the name you typed. With a name typed, an exact match and then names starting with it always come first, whatever the sort.Search
Sort directionFlips the order: ↑ ascending, ↓ descending. It applies to Name, Thickness and Camber; Relevance is always best match first.Search
SourceWhere a surface's geometry comes from: one of your saved wing designs, a generated straight-tapered stabiliser from area and aspect ratio, or a reference template. Each is a full designer document.Trim
Span eff. eOswald span efficiency: 1 for an elliptical loading, less for anything else, fitted to the spanwise loading with a Glauert series. Induced drag scales with 1/e.Wing analysis
Spanwise loadingLocal lift coefficient along the half-span at the reference angle, from a vortex-lattice solve on either method. Dashed is the elliptical ideal; dotted is each station's own Clmax at its local Re.Wing analysis
Spanwise panelsStrips across the half-span for a VLM run: 10 or 16. The solver clamps at 16 and the price follows the clamped count (2 credits up to 10, 3 credits above), so asking for more buys nothing.Wing analysis
SpeedShows and reads every speed on this tab in m/s, km/h or knots: the inputs, the results header and the plot axes. The solver always works in m/s.Wing analysis
Speed(m/s or kn)The speed to trim at, in the unit chosen beside it; in Sweep, the first and last speeds. A template opens at the speed its rig was sized for.Trim
SpeedOne condition the section must serve. Each row becomes an operating point: Re = ρ·V·c/μ on the mean chord and CL = L / (½ρV²·S) from the load. Add a row for cruise, top speed, take-off.Mission
Speed unitm/s or knots for every speed on this page: the inputs, the row list and the chart. The request is sent in m/s.Trim
Stab incidence(deg)The free surface's solved incidence, nose-up positive: the setting that zeroes the moment at this speed. Negative means the stabiliser is set to push down.Trim
Stall gentlenessShare of lift lost 3° past the peak; a gentle stall scores better than a higher, abrupt one. Lower is better: scaled 0–1 across the matched candidates and multiplied by this weight.Mission
Stall marginHeadroom before the first station stalls at the cruise point: the smallest Clmax(y) − Cl(y) along the span, as ΔCl. A run saved before this existed shows Δα to the 3D polar peak instead, and says so.Wing analysis
Standard seriesEight textbook planforms, each built at the span and aspect ratio you type. λ is taper ratio, AR aspect ratio, Λ the true quarter-chord sweep. Applying one changes the shape only; sections and operating point stay.Wing designer
Starting AirfoilThe library section the solve starts from. Its polar is the dashed "Starting" curve and the baseline for the headline improvement. Any section works; a start near your thickness and camber limits converges fastest.Optimize
Static margin(c̄ and mm)Neutral point aft of the CG, as a fraction of the main wing's c̄ and in mm; positive is statically stable. Wing plus tail only: masts and pods move the thrust and the loads, not this.Trim
Static margin(% MAC)Neutral point minus CG, as a percentage of MAC. Positive is statically stable: a nose-up disturbance makes a nose-down moment. Larger is steadier and needs more stabiliser trim to fly level.Wing designer
StepSpacing between sweep speeds. Rows = (high − low) ÷ step + 1, capped at 20; widen the step when the count turns amber, or the route refuses the request.Trim
Suitability(%)100·e^(−10·drag), where drag is each performance point's matched Cd times its weight share, summed. 100 would be zero drag. It is the drag-only scale and does not change when other criteria are weighted.Mission
Surface load(N)Lift on each surface, and its share of the weight. A negative load is a download on the stabiliser, which the main wing then carries on top of the weight.Trim
Sweep(deg)Where the tip leading edge lands: tan(sweep) × half-span, minus a quarter of the taper. It is not the quarter-chord or the leading-edge sweep; the real angles it produces are under Derived Parameters.Wing designer
Sweep ¼c(deg)The real quarter-chord sweep, measured off the planform the Sweep control built: the angle of the root-to-tip line through each chord's quarter point. This is the Λ a textbook or XFLR5 means.Wing designer
Sweep LE(deg)The real leading-edge sweep: the angle of the straight line from the root leading edge to the tip leading edge. Larger than Λ¼c on a tapered wing, because the taper rakes the LE back.Wing designer
SymmetryOn, every lower weight is forced to minus its upper weight, the leading-edge weight to 0, and N1 and N2 to 0.5 and 1. Moving the TE angle or generating a cambered NACA turns it off; a section loaded while it is on is symmetrised.Kulfan canvas
T and C(% chord)T: maximum thickness, C: maximum camber, both as a percentage of chord, measured from the drawn geometry. The table under the section preview adds where each peaks.Compare
Tail ARStabiliser aspect ratio, span² over area. It sets how much lift the tail makes per degree. 3–5 is the band the card calls responsive without stalling before the wing.Wing designer
Tail area(m²)Stabiliser planform area, both sides together, in m². With the arm it sets the tail volume V_H; the cm² echo under the inputs is for foil builders, who size in cm².Wing designer
Tail arm(mm)From the wing's quarter chord at its MAC to the stabiliser's quarter chord at its MAC, in mm. On a hydrofoil it is roughly the fuselage length.Wing designer
Tail volumeV_H = S_h · l_h / (S · MAC): the tail's area times its arm, scaled by the wing's. The one number that says how much authority the tail has; the card shows where it sits among the site's rigs.Wing designer
Taper ratioTip chord over root chord, λ. About 0.35 comes closest to an elliptical span loading on a straight wing; below that the tip loads up and wants washout.Wing designer
Target AR, hold areaReaches this aspect ratio without changing the area: span grows by √(new/current) and every chord shrinks by the same factor. Exact for a curved outline, because it works on ratios.Wing designer
Target AR, hold spanReaches this aspect ratio without changing the span: every chord is scaled by current/new AR, so the area moves instead.Wing designer
Target area(m²)Scales the whole wing uniformly to this planform area: span and chords by the same factor, so aspect ratio, taper and the spline shape are unchanged.Wing designer
Target load(kg)The mass the wing must carry; the solver turns it into lift = mass × g. Negative is downforce, for a stabiliser. At each speed the angle is solved so the lift matches, on the pre-stall branch of the lift curve.Wing analysis
TE Angle(deg)The angle of the mean line at the trailing edge, positive downward. Dragging it shifts both last weights by the same amount, which turns the tail without changing its wedge, and switches symmetry off.Kulfan canvas
TE angle(deg)The wedge angle between the surfaces at the trailing edge of the optimized section, the figure the TE wedge constraint bounds.Optimize
TE Thickness(% chord)The trailing-edge gap as a percentage of chord, up to 2. Half is added to the upper surface and half taken from the lower, growing linearly from the nose, so only the tail moves. Both exports carry it.Kulfan canvas
TE thickness(mm)Opens every station's trailing edge to at least this, up to 10 mm, for a cutter or a printer that cannot make a knife edge. 0 keeps each section's own edge. The viewer always shows the section as drawn.Wing designer
TE wedge angle(deg)The least angle the two surfaces may close at. Drag minimisation pulls the tail toward a cusp no shop can make and no structure can hold; opens on, at 5°.Optimize
Thickness(% chord)Maximum thickness as a percentage of chord, measured from the drawn geometry. Thicker sections stall more gently and hold more structure; thinner ones have less drag at low lift.Foil page
Thickness(% chord)Maximum upper-minus-lower distance of the drawn section, as a percentage of chord, with the scalars applied. Measured on the same points the exports use.Kulfan canvas
Thickness(% chord)Keeps the maximum thickness between the two values, as a percentage of chord. Opens on, at 8 to 18. Without it the solver thins the section until the spar no longer fits.Optimize
Thickness(% chord)Maximum thickness of the optimized section, as a percentage of chord. Compare it with the Thickness bound: a value sitting on the bound means the constraint was doing the work.Optimize
Thickness(% chord)Keep only sections whose maximum thickness, as a percentage of chord, lies between Min and Max. A hard filter applied before any scoring: structure is a requirement, not a preference.Mission
Thickness(% chord)Keeps sections whose maximum thickness, as a percentage of chord, lies between the two values. Opens at 0 to 30, which is the whole library.Search
Thickness ScalarMultiplies the thickness half of every weight pair, (upper − lower)/2, leaving the camber half alone. 1 is the section as loaded. Exports and hand-offs carry it; the parameter box does not.Kulfan canvas
Thickness, Camber, TE(% chord)The start as it will be drawn: maximum thickness and camber measured from its geometry, and the trailing-edge gap it carries, all as percentages of chord. Freeze TE thickness keeps the last one.Optimize
Thrust lineWhere the thrust acts in z. Through the CG adds no moment. At a height z puts the thrust's arm into the balance: nose-up or nose-down as the line sits below or above the CG.Trim
Thrust zHeight of the thrust line, up positive, in the craft frame whose origin is the main wing's root leading edge.Trim
TipThe section at the tip. Leave it empty and the tip is the root section. Set it and every station between is blended from root to tip, in the viewer, the analysis and the export alike.Wing designer
Tip chord(mm)Chord at the tip station, from 1 mm. A shorter tip means a lower Reynolds number there and, with no twist, a tip that loads up; the tip rondure's reach is a fraction of it.Wing designer
Tip twist(deg)Geometric angle of the tip section relative to the root, -15 to 10°. Negative is washout: the tip flies at a lower angle and stalls after the root. The profile between is the twist curve.Wing designer
Top recommended airfoilsDesign Custom hands the points and the top section to Optimize; Compare Top 5 overlays the first five; Export Top 5 downloads each as DAT or DXF (1000 mm chord); Copy Summary copies rank, name, suitability, thickness and camber.Mission
Trim vs speedOne row per sweep speed: trim α, the free surface's setting and the static margin in mm. A refused row could not carry the load, or needed an angle outside the ±20° window the section model is trusted in.Trim
Trim α(deg)Body angle of attack that carries the weight at this speed with the moment about the CG zero. The reference wing's chord line is the body axis.Trim
Trimmed L/DLift over drag for the whole craft at this trim point. The caption says how much of the drag is induced, or how much comes from the drag elements when there are any.Trim
UnitThe unit every speed on this card is typed in. Knots and km/h are converted to m/s before Re and CL are computed. Changing the unit does not convert the numbers already typed.Mission
Upload .datAdds a Selig-format .dat as ↑: two columns x y, chord normalised, split at the midpoint into the two surfaces. It has no stored polars; Run NeuralFoil computes them. Signed in, the cloud button saves it to your account.Compare
Use the resultCompare runs the optimized section beside the library; Root or Tip opens the wing designer with it in that slot; Save puts it in your account. DAT and DXF are the shape, JSON the CST plus the request that made it.Optimize
V min / V max / V step(m/s, km/h or knots)The speeds a constant-lift run walks, in the unit selected above, one row per step. A speed too slow to carry the load before the wing stalls is reported as infeasible, not trimmed.Wing analysis
V_HTail volume coefficient, V_H = S_h · l_h / (S · c̄): the tail's area and arm against the wing's area and mean chord. Free and closed-form, the same number as the designer's stabiliser card.Trim
Velocity(m/s, km/h or knots)The one speed an α sweep is run at, in the unit selected above; sent to the solver in m/s. With the fluid it sets the Reynolds number every section polar is read at.Wing analysis
WeightHow much this point's drag counts, 0.1 to 100; the weights are normalised, so only their ratio matters. A heavier cruise point and a light take-off point lets the solver trade a little drag at one for the other.Optimize
WeightRelative importance of a performance point. Weights are normalised to shares across the performance points, and each point's matched drag is multiplied by its share. A constraint point has no weight.Mission
Wing area(m² or ft²)Planform area of this surface. With the load it gives the lift coefficient, CL = L / (q·S); with the span it gives the mean chord the Reynolds number is computed on.Mission
Wing loading(Pa)Weight over planform area, in pascals, at two fixed masses: 25 kg (a large RC model or a child on a foil) and 85 kg (an adult rider). Divide by ½ρV² for the lift coefficient the wing must fly at.Wing designer
Wingspan(m or ft)Tip-to-tip span. Area over span is the mean chord every operating point's Reynolds number is computed on; span squared over area is the aspect ratio shown beside it.Mission
x(mm or m)The surface's root leading edge, aft of the reference wing's root leading edge. Typing the Arm moves this instead.Trim
x(mm or m)Where a drag element acts, aft of the wing root leading edge. Its drag times its height above or below the CG is a moment the balance carries.Trim
z(mm or m)Height of the surface's root leading edge, up positive. On the hydrofoil template the stabiliser sits level with the wing and the rider a metre above both.Trim
z(mm or m)Height of the element, up positive: for a mast or strut, the middle of its immersed length; for a drag area, where the drag acts.Trim
Zero-lift alphaThe angle of attack where lift crosses zero with the flow attached. Negative for a cambered section; the lift curve rises from here at about 0.1 per degree.Foil page
α min / α max / α step(deg)The angles of attack an α sweep walks, one polar row per step. Past about ±20° the section model is outside the range it is trusted in, so a wider sweep mostly shows where the model stops.Wing analysis
α sweep / Constant liftTwo kinds of run. α sweep holds one speed and walks angle of attack: the wing's polar. Constant lift holds a load and solves the angle at each speed: what carrying it costs across the envelope.Wing analysis