# Sections along the span

The planform says how big the wing is at each station; the sections say what shape it has there. The designer takes two, a root and a tip, and blends every station between them. The question at this stage is which two, and whether they should differ at all. On the Wing Foil — Freeride the answer is one section, n63412, at both ends; a wing that needs a gentler tip stall is the case for a second.

## Choosing the root and the tip

The Airfoil Sections card has a box for each. Type to search the library by name; the root is required before the viewer draws anything. Leave the tip box empty and the tip is the root section, one shape scaled down the span. Pick a tip and the wing changes between the two.

![The Airfoil Sections card at the top of the left column: the root slot showing n63412 with its Re readout and Find and Optimize buttons, the tip slot, and the Operating Conditions line, each ringed.](https://media.foil.tools/docs/shots/wing-sections-slots.04af3786990a.webp)

*The sections are at the top of the left column. Each slot carries its own Reynolds number and the way to Mission or Optimize; the line under them is the operating point it is worked out from.*

What to put at the tip is a stall question more than a drag question. A tapered wing with no twist loads its tip almost as hard as its root, so a tip section that stalls at a higher angle, thinner or less cambered, keeps the tip flying after the root has let go. The other way to get that is washout, on the [next page](/docs/wing-twist-dihedral). The reference designs use one section throughout, so a second one is a deliberate change from a working design.

**Recording: Picking a tip section** (33 s, https://media.foil.tools/docs/wing-tip-section.4e42143c1486.mp4)

> The tip can carry its own section. A thinner tip stalls later than the root, so the wing stalls inboard first.
> Re ≈ beside each section is that section's own, from its chord: the tip sits lower, so read the tip section at its own Reynolds number.
> Find → takes the section's Reynolds number and lift coefficient to Mission; Optimize → takes them to the optimizer.

## How they blend

Every station is a linear mix of the two: at a fraction t of the way to the tip, the station is root + (tip − root) · t. The viewer blends the drawn ordinates of the two sections, which share one chordwise sampling; the analysis blends their CST weights the same way at 20 stations; the export lofts through sections the CAD sidecar blends from the same two parameter sets. Three renderings, one rule, so what you see, what is analysed and what you machine describe the same wing. Each station is then scaled to its chord, placed on the leading edge you drew, lifted by the dihedral curve and rotated by the twist curve.

The library's sections nearly all carry eight CST weights a side; a handful carry nine or twelve. The viewer blends any pair, but the analysis blends weight by weight and does not yet handle a root and a tip with different counts, so keep to a matching pair when a second section goes on. More than two sections, placed anywhere along the span, is planned and not on the site yet.

## The Reynolds number beside each section

Under each box is Re ≈, the Reynolds number that section flies at: its own chord, the operating speed and the fluid, Re = ρVc/μ. On the example the root is at 963k and the tip, with its shorter chord, at 412k. Those are the numbers to type into "Run it at your Reynolds number" on each section's [foil page](/docs/foil-page): a tip section is judged at the tip's Re, not the root's. [Reynolds number](/docs/reynolds-number) explains what the figure changes.

## Find and Optimize

The speed, fluid and design lift coefficient the readouts use are the **Operating conditions** under the boxes. They come from [Mission](/docs/mission) or from a reference design, which carries its own (7 m/s, sea water, CL 0.35 on the example); the /input link takes you back to change them.

Each slot has two buttons. **Find →** opens Mission with that slot's Reynolds number and the design CL filled in, so the selector ranks sections for exactly this station, and its results offer "Apply to root" or "Apply to tip" on each candidate. **Optimize →** opens [Optimize](/docs/optimize) starting from the section in the slot, at its Re and CL, and the optimized shape comes back to the same slot; it needs a section in the slot first. Both carry every operating point Mission knows, when there is more than one.

## What this hands on

Two named sections at their stations, saved with the design: the [analysis](/docs/wing-analysis) blends them to make its polars, and the [export](/docs/wing-export) lofts through them. A section you optimized on the way is saved to your account on its own, so another wing can start from it.

## Controls on this page

| Control | What it does | Units |
| --- | --- | --- |
| Root | The section at the centreline. Type to search the library. With no tip section it is the whole wing; the viewer, the analysis and the export all draw from the same CST parameters. |  |
| Tip | The section at the tip. Leave it empty and the tip is the root section. Set it and every station between is blended from root to tip, in the viewer, the analysis and the export alike. |  |
| Re ≈ | The Reynolds number at this section, from its own chord, the operating speed and the fluid: Re = ρVc/μ. The tip, with a shorter chord, flies at a lower Re than the root; read each section's polars there. |  |
| Find → | Opens Mission with this slot's Reynolds number and the design CL already filled in, so the selector ranks sections for exactly this station. Its results offer "Apply to root" or "Apply to tip". |  |
| Optimize → | Opens Optimize starting from this slot's section at its Reynolds number and CL. The optimized shape comes back to the same slot. Needs a section in the slot first. |  |
| Operating conditions | Speed, fluid and design lift coefficient. They set the Re ≈ beside each section and what Find → and Optimize → ask for. Set them on Mission, or load a reference design, which carries its own. |  |
| Full span | Twice the half-span: the whole wing, tip to tip. Every length you type is for one half; the derived figures and the export are for both. | mm |
| Planform area | Both halves, integrated from the drawn leading and trailing edges at 40 stations, not from a trapezoid, so a curved outline counts. It is the S_ref the analysis reports. | m² |
| Aspect ratio | Full span squared over planform area. Higher means less induced drag for the same lift and a heavier root bending load; a glider is 20 and up, a freeride foil about 9. |  |
| Taper ratio | Tip chord over root chord, λ. About 0.35 comes closest to an elliptical span loading on a straight wing; below that the tip loads up and wants washout. |  |
| Sweep ¼c | The real quarter-chord sweep, measured off the planform the Sweep control built: the angle of the root-to-tip line through each chord's quarter point. This is the Λ a textbook or XFLR5 means. | deg |
| Sweep LE | The real leading-edge sweep: the angle of the straight line from the root leading edge to the tip leading edge. Larger than Λ¼c on a tapered wing, because the taper rakes the LE back. | deg |
| MAC | Mean aerodynamic chord, ∫c² dy / S over the half-wing. The reference length for Reynolds number at the wing level, for pitching moment and for the static margin. | mm |
| MAC spanwise | How far out from the centreline the mean aerodynamic chord sits. Where the half-wing's lift acts, near enough, so it is the arm the root bending moment works on. | mm |
| Wing loading | Weight over planform area, in pascals, at two fixed masses: 25 kg (a large RC model or a child on a foil) and 85 kg (an adult rider). Divide by ½ρV² for the lift coefficient the wing must fly at. | Pa |
| Target area | Scales the whole wing uniformly to this planform area: span and chords by the same factor, so aspect ratio, taper and the spline shape are unchanged. | m² |
| Target AR, hold area | Reaches this aspect ratio without changing the area: span grows by √(new/current) and every chord shrinks by the same factor. Exact for a curved outline, because it works on ratios. |  |
| Target AR, hold span | Reaches this aspect ratio without changing the span: every chord is scaled by current/new AR, so the area moves instead. |  |
| Standard series | Eight textbook planforms, each built at the span and aspect ratio you type. λ is taper ratio, AR aspect ratio, Λ the true quarter-chord sweep. Applying one changes the shape only; sections and operating point stay. |  |
| Reference designs | 15 complete wings at real sizes, from a surf foil to a bizjet. Loading one replaces everything: planform, sections, tip cap, export settings and the speed, fluid, CL and mass it was sized for. |  |
| LE and TE points | Add a point to the leading or trailing edge and drag it: the edge becomes a smooth curve through every point. Diamonds at root and tip set the end tangents; the root one is locked level so the two halves meet without a kink. |  |
| Half-span | Centreline to tip, for one half; the wing is mirrored about the root. 100 to 20,000 mm. Interior points keep their position in mm, so lengthen the span and they stay where they were. | mm |
| Root chord | Leading edge to trailing edge at the centreline, 10 to 5,000 mm. Sets the root section's Reynolds number and, with the tip chord, the taper ratio. | mm |
| Tip chord | Chord at the tip station, from 1 mm. A shorter tip means a lower Reynolds number there and, with no twist, a tip that loads up; the tip rondure's reach is a fraction of it. | mm |
| Sweep | Where the tip leading edge lands: tan(sweep) × half-span, minus a quarter of the taper. It is not the quarter-chord or the leading-edge sweep; the real angles it produces are under Derived Parameters. | deg |
| Dihedral | Angle of the tip above the root, -20 to 30°; negative is anhedral, the tips below the root. Sets the end of the front-view curve; points on that curve shape the path between. | deg |
| Tip twist | Geometric angle of the tip section relative to the root, -15 to 10°. Negative is washout: the tip flies at a lower angle and stalls after the root. The profile between is the twist curve. | deg |
| Bias | Where along the tip chord the rounded cap reaches furthest out, as a percentage from the leading edge, 5 to 95. Tangency to the edges limits the range; the readout says where the peak actually landed. | % chord |
| Reach | How far the cap extends past the tip station, as a percentage of half the tip chord: at 100 it reaches half a tip chord outboard; at 0 the tip is cut flat. The export carries the same cap. | % tip chord |
| Loft sections | How many stations the exporter lofts through between root and tip, 10 to 80, default 30. More follows a curved edge or a twist profile more closely and takes longer to build. |  |
| TE thickness | Opens every station's trailing edge to at least this, up to 10 mm, for a cutter or a printer that cannot make a knife edge. 0 keeps each section's own edge. The viewer always shows the section as drawn. | mm |
| Format | STEP is the exact lofted solid for CAD: shell it, split it, cut moulds from it. STL is the same solid as a triangle mesh for slicers and mesh tools. Both are in millimetres and hold both halves. |  |
| Generate 3D wing | Builds the solid in CAD on the server and downloads it, usually in under 20 s; it stops at 90 s and says why. Needs a sign-in and a root section. The file is the same loft the viewer shows. |  |
| 3D preview | The wing lofted live from the controls, both halves. Seven camera views on keys 1–7, Ortho or Persp on O, the ground grid on G, Expand on E. Drag to orbit, scroll to zoom, right-drag to pan. |  |
| Shading | Solid shows the surface as a painted composite would read. Solid+wire adds the station rings and the leading, trailing and quarter-chord lines over it. Wires shows only those, so the loft is visible through the wing. |  |
| Tail area | Stabiliser planform area, both sides together, in m². With the arm it sets the tail volume V_H; the cm² echo under the inputs is for foil builders, who size in cm². | m² |
| Tail arm | From the wing's quarter chord at its MAC to the stabiliser's quarter chord at its MAC, in mm. On a hydrofoil it is roughly the fuselage length. | mm |
| Tail AR | Stabiliser aspect ratio, span² over area. It sets how much lift the tail makes per degree. 3–5 is the band the card calls responsive without stalling before the wing. |  |
| CG | Centre of gravity as a fraction of the wing MAC, measured aft of the MAC leading edge. 0.25 is the wing's own aerodynamic centre; the static margin is how far the neutral point sits behind this. | × MAC |
| Tail volume | V_H = S_h · l_h / (S · MAC): the tail's area times its arm, scaled by the wing's. The one number that says how much authority the tail has; the card shows where it sits among the site's rigs. |  |
| Neutral point | Stick-fixed neutral point of wing plus tail, as a fraction of MAC and in mm: the CG position at which the rig would be neutrally stable. No fuselage; one moves it forward by about 0.05–0.10 MAC. |  |
| Static margin | Neutral point minus CG, as a percentage of MAC. Positive is statically stable: a nose-up disturbance makes a nose-down moment. Larger is steadier and needs more stabiliser trim to fly level. | % MAC |
| Estimate terms | The four factors the neutral point is built from: area ratio S_h/S, arm in chords l_h/MAC, the tail's lift slope over the wing's, and 1 − dε/dα, how much of the wing's downwash the tail sits in. |  |
