# Planform

You have a section and the operating point it was chosen for. The next question is the outline of the wing that carries it: how long, how wide at the root and the tip, how far back the tip sits. The Design tab of the [wing designer](/wing) answers it with four numbers and two draggable edges, and reports everything that follows under Derived Parameters. This page follows the Wing Foil — Freeride reference design: 1.0 m of span, 145 mm at the root, 62 mm at the tip.

**Figure: Section to STEP**

1. Sections: the root and tip, each with its own Reynolds number
2. Planform: half-span, chords, sweep
3. Twist and dihedral: washout and the tip cap
4. The loft: drawn in the 3D viewer from the stations
5. Analysis: AeroBuildup or VLM on the same stations
6. Export: STEP or STL, the same loft written by pywing

One loft, drawn twice: the viewer draws it in the browser and pywing writes the same stations and tip cap to the file.

## Half-span and chords

Everything you type describes one half of the wing; the other half is a mirror about the root. **Half-span** is centreline to tip, 100 to 20,000 mm: 500 mm on the example, 1.0 m in the derived figures and the export. **Root chord** (10 to 5,000 mm) and **Tip chord** (from 1 mm) set the two end stations; their ratio is the taper, λ = 0.43 here. Chord also sets each section's Reynolds number, which is why [Sections along the span](/docs/wing-sections) shows a readout beside each one.

![The Top View — Planform card with the freeride planform drawn, its half-span 500 mm, root chord 145 mm, tip chord 62 mm and sweep inputs ringed, and the + LE pt button ringed.](https://media.foil.tools/docs/shots/wing-planform-inputs.d63208a5fef8.webp)

*The planform card: four numbers under the drawing, and handles on the drawing itself. The buttons add a control point to the leading or trailing edge.*

## What Sweep means here

The **Sweep** box is not the quarter-chord sweep, and not the leading-edge sweep either. It places the tip leading edge at tan(sweep) × half-span minus a quarter of the root-to-tip taper, a formula whose taper term carries the opposite sign to the one a straight quarter-chord line needs. It is kept as it is because correcting it would silently reshape every saved wing. So the box corresponds to no named angle: the freeride foil reads 9.675 in the box and has a quarter-chord sweep of 5.0°.

The angles that mean something are under Derived Parameters. **Sweep ¼c** is the true quarter-chord sweep, measured off the planform that was built; **Sweep LE** is the angle of the root-to-tip leading-edge line, 7.3° on the example. When XFLR5, OpenVSP or a textbook says Λ, it means the first. Reference designs and the standard series are authored by true Λ¼c and converted. To hit a quarter-chord sweep yourself, change the box and watch the derived line.

**Recording: Planform: sweep and the derived angles** (37 s, https://media.foil.tools/docs/wing-planform.31884157793c.mp4)

> Start from the Wing Foil — Freeride reference design: 1 m span, 145 mm root, 62 mm tip, NACA 63-412.
> Sweep here is the sweep of a line a quarter chord ahead of the leading edge, not the leading edge itself; the real angles are under Derived Parameters.
> Half-span, root chord and tip chord set everything derived: area, aspect ratio, taper, MAC and the wing loading.

## Derived parameters

Read from the drawn geometry, not from a trapezoid: the edges are sampled at 40 stations and integrated, so a curved outline counts, and the area and aspect ratio here are the S_ref and AR the analysis reports. **Planform area** is both halves, 1141 cm² on the example; **aspect ratio** is span² over area, 8.8; **MAC** is the mean aerodynamic chord, 120 mm, and **MAC spanwise** how far out it sits. **Wing loading** is weight over area at two fixed masses, 25 kg and 85 kg: a large RC model or a child, and an adult rider. Divide it by ½ρV² at your speed for the lift coefficient the wing must fly at.

![The Derived Parameters card in the left column ringed: full span, planform area, aspect ratio, taper ratio, both sweep angles, MAC and wing loading.](https://media.foil.tools/docs/shots/wing-derived.223d772c5c41.webp)

*Derived Parameters, in the left column, follow every edit.*

## The edge control points

The four numbers fix the ends of the leading and trailing edges; **+ LE pt** and **+ TE pt** add an interior point, and dragging it bends the edge through it. The diamond handles set the end tangents: the root one is locked level so the two halves meet without a kink, the tip one is free, which is what makes a raked tip. Reference designs carry no interior points; their shape is entirely in the end handles.

## Scale geometry

Three ways to resize without redrawing: **Target area** scales span and chords together, keeping AR, taper and shape; **Target AR, hold area** grows the span and shrinks the chords by the same ratio; **Target AR, hold span** scales the chords alone.

![The Scale Geometry card in the left column ringed, with its Target area, Target AR hold area and Target AR hold span rows and their Apply buttons.](https://media.foil.tools/docs/shots/wing-scale-geometry.bb76e88e7b66.webp)

*Scale Geometry resizes the planform to a target area or aspect ratio and keeps its shape.*

## Standard series

Eight textbook planforms, rectangular to delta, built at the span and aspect ratio you type. Each card reads λ (taper), AR and Λ (true quarter-chord sweep), with the trade-off the shape is known for. Applying one changes the planform only.

![The top of the wing designer's right column with the Standard Series and Reference Designs panels ringed, both closed.](https://media.foil.tools/docs/shots/wing-series-and-references.fe693a938e7a.webp)

*Two starting points sit at the top of the designer: the standard series and the reference designs. Both open on a click.*

## Reference designs

Complete wings at real sizes: hydrofoils, RC aircraft and full-scale aircraft. Loading one replaces the whole design, including the speed, fluid, lift coefficient and mass it was sized for.

![The Reference Designs panel open on its watersports hydrofoils row, with the Wing Foil — Freeride card ringed: 1.00 m span, 1141 cm², aspect ratio 8.8, NACA 63-412.](https://media.foil.tools/docs/shots/wing-reference-designs.09730182c358.webp)

*Reference Designs, open. The freeride wing foil is the worked example these docs use; a click replaces the whole design with it.*

## Stabiliser estimate

The card under Derived Parameters sizes a tail against this wing before any solver runs: area, arm, aspect ratio and the CG as a fraction of MAC in; tail volume, neutral point and static margin out. It has no fuselage, which moves the neutral point forward by about 0.05–0.10 MAC on aircraft. [Trim](/docs/trim) solves the rig properly.

![The Stabiliser (estimate) card in the left column ringed, with inputs for tail area, tail arm, tail aspect ratio and CG as a fraction of MAC.](https://media.foil.tools/docs/shots/wing-stabiliser.65eafad39277.webp)

*The stabiliser estimate sits under Derived Parameters: tail volume and the neutral point, from four numbers.*

## What each control moves

An effects table will show what a change of span, root chord, tip chord and sweep does to two reference wings, a hydrofoil in salt water and an RC wing in air: (L/D)max, drag at the cruise point, span efficiency and where the stall starts.

**What each planform control changes, on two reference wings**

| Wing | Change | (L/D) max | CD at cruise | Span efficiency e | First stall η |
| --- | --- | --- | --- | --- | --- |
| Wing Foil — Freeride | Baseline | 29.6 | 0.0110 | 0.82 | 0.72 |
| Wing Foil — Freeride | Half-span +10% | +2.3% | −10.6% |  |  |
| Wing Foil — Freeride | Half-span −10% | −4.0% | +15.9% |  |  |
| Wing Foil — Freeride | Root chord +10% | −2.2% | −4.2% |  |  |
| Wing Foil — Freeride | Root chord −10% | +2.0% | +5.1% | −0.6% | −0.13 |
| Wing Foil — Freeride | Tip chord +10% | −0.9% | −1.7% |  | −0.06 |
| Wing Foil — Freeride | Tip chord −10% | +0.8% | +1.8% |  |  |
| Wing Foil — Freeride | Sweep +5° |  | +1.2% | −0.5% |  |
| Wing Foil — Freeride | Sweep −5° |  | −1.0% |  | −0.69 |
| Wing Foil — Freeride | Tip twist +1° |  |  |  |  |
| Wing Foil — Freeride | Tip twist −1° |  |  |  | −0.06 |
| Wing Foil — Freeride | Dihedral +2° |  |  |  |  |
| Wing Foil — Freeride | Dihedral −2° |  |  |  |  |
| RC Trainer | Baseline | 20.3 | 0.0280 | 0.80 | 0.03 |
| RC Trainer | Half-span +10% | +3.2% | −16.5% |  |  |
| RC Trainer | Half-span −10% | −3.3% | +24.4% |  |  |
| RC Trainer | Root chord +10% | −0.9% | −4.8% | +1.0% |  |
| RC Trainer | Root chord −10% | +1.1% | +5.8% | −1.8% |  |
| RC Trainer | Tip chord +10% | −1.8% | −3.7% | −0.8% |  |
| RC Trainer | Tip chord −10% | +2.2% | +4.2% |  |  |
| RC Trainer | Sweep +5° |  |  | −0.9% |  |
| RC Trainer | Sweep −5° |  |  |  |  |
| RC Trainer | Tip twist +1° |  |  |  |  |
| RC Trainer | Tip twist −1° |  |  |  |  |
| RC Trainer | Dihedral +2° |  |  |  |  |
| RC Trainer | Dihedral −2° |  |  |  |  |

Source: pyfoil ac7e53e /analyze-wing, AeroBuildup, constant-lift sweep 4–30 m/s in 1 m/s steps, 20 stations, NeuralFoil small, run 2026-11-11 on a local pyfoil. Wing Foil — Freeride (template wing-foil-freeride; n63412; half-span 500 mm, chords 145/62 mm, sweep 9.675 (quarter-chord 5.0°), dihedral -2°, tip twist -2°) at 95 kg and 7 m/s in water (sea) (ρ 1025, μ 0.00108). RC Trainer (template rc-trainer; clarky; half-span 700 mm, chords 250/250 mm, sweep 0 (quarter-chord 0.0°), dihedral 3°, tip twist 0°) at 2.5 kg and 15 m/s in air (ρ 1.225, μ 0.00001789). (L/D) max is the best feasible row of the sweep; CD at cruise is the row at the template's speed; e and the first-stall station η (fraction of the half-span, from stall_progression) are pyfoil's summary at its best-L/D row. Each change is one designer control moved from the baseline (lengths ±10%, angles as absolute steps); the cells are the change relative to the baseline row, and anything under 0.5% (0.005 of the half-span for η) is left blank. η is where the stall margin is lowest; across the span that margin varies by 2% on the Wing Foil — Freeride and 18% on the RC Trainer, and where it is nearly flat a small change moves η a long way without meaning much.

## What this hands on

A planform, with its sections and twist, is a saved design: name it under Saved Designs and it is yours to run on the [Analyze tab](/docs/wing-analysis), to balance on [Trim](/docs/trim), and to [export](/docs/wing-export) as STEP or STL for the shop. The next two pages cover the sections along the span and the twist, dihedral and tip.

## Controls on this page

| Control | What it does | Units |
| --- | --- | --- |
| Root | The section at the centreline. Type to search the library. With no tip section it is the whole wing; the viewer, the analysis and the export all draw from the same CST parameters. |  |
| Tip | The section at the tip. Leave it empty and the tip is the root section. Set it and every station between is blended from root to tip, in the viewer, the analysis and the export alike. |  |
| Re ≈ | The Reynolds number at this section, from its own chord, the operating speed and the fluid: Re = ρVc/μ. The tip, with a shorter chord, flies at a lower Re than the root; read each section's polars there. |  |
| Find → | Opens Mission with this slot's Reynolds number and the design CL already filled in, so the selector ranks sections for exactly this station. Its results offer "Apply to root" or "Apply to tip". |  |
| Optimize → | Opens Optimize starting from this slot's section at its Reynolds number and CL. The optimized shape comes back to the same slot. Needs a section in the slot first. |  |
| Operating conditions | Speed, fluid and design lift coefficient. They set the Re ≈ beside each section and what Find → and Optimize → ask for. Set them on Mission, or load a reference design, which carries its own. |  |
| Full span | Twice the half-span: the whole wing, tip to tip. Every length you type is for one half; the derived figures and the export are for both. | mm |
| Planform area | Both halves, integrated from the drawn leading and trailing edges at 40 stations, not from a trapezoid, so a curved outline counts. It is the S_ref the analysis reports. | m² |
| Aspect ratio | Full span squared over planform area. Higher means less induced drag for the same lift and a heavier root bending load; a glider is 20 and up, a freeride foil about 9. |  |
| Taper ratio | Tip chord over root chord, λ. About 0.35 comes closest to an elliptical span loading on a straight wing; below that the tip loads up and wants washout. |  |
| Sweep ¼c | The real quarter-chord sweep, measured off the planform the Sweep control built: the angle of the root-to-tip line through each chord's quarter point. This is the Λ a textbook or XFLR5 means. | deg |
| Sweep LE | The real leading-edge sweep: the angle of the straight line from the root leading edge to the tip leading edge. Larger than Λ¼c on a tapered wing, because the taper rakes the LE back. | deg |
| MAC | Mean aerodynamic chord, ∫c² dy / S over the half-wing. The reference length for Reynolds number at the wing level, for pitching moment and for the static margin. | mm |
| MAC spanwise | How far out from the centreline the mean aerodynamic chord sits. Where the half-wing's lift acts, near enough, so it is the arm the root bending moment works on. | mm |
| Wing loading | Weight over planform area, in pascals, at two fixed masses: 25 kg (a large RC model or a child on a foil) and 85 kg (an adult rider). Divide by ½ρV² for the lift coefficient the wing must fly at. | Pa |
| Target area | Scales the whole wing uniformly to this planform area: span and chords by the same factor, so aspect ratio, taper and the spline shape are unchanged. | m² |
| Target AR, hold area | Reaches this aspect ratio without changing the area: span grows by √(new/current) and every chord shrinks by the same factor. Exact for a curved outline, because it works on ratios. |  |
| Target AR, hold span | Reaches this aspect ratio without changing the span: every chord is scaled by current/new AR, so the area moves instead. |  |
| Standard series | Eight textbook planforms, each built at the span and aspect ratio you type. λ is taper ratio, AR aspect ratio, Λ the true quarter-chord sweep. Applying one changes the shape only; sections and operating point stay. |  |
| Reference designs | 15 complete wings at real sizes, from a surf foil to a bizjet. Loading one replaces everything: planform, sections, tip cap, export settings and the speed, fluid, CL and mass it was sized for. |  |
| LE and TE points | Add a point to the leading or trailing edge and drag it: the edge becomes a smooth curve through every point. Diamonds at root and tip set the end tangents; the root one is locked level so the two halves meet without a kink. |  |
| Half-span | Centreline to tip, for one half; the wing is mirrored about the root. 100 to 20,000 mm. Interior points keep their position in mm, so lengthen the span and they stay where they were. | mm |
| Root chord | Leading edge to trailing edge at the centreline, 10 to 5,000 mm. Sets the root section's Reynolds number and, with the tip chord, the taper ratio. | mm |
| Tip chord | Chord at the tip station, from 1 mm. A shorter tip means a lower Reynolds number there and, with no twist, a tip that loads up; the tip rondure's reach is a fraction of it. | mm |
| Sweep | Where the tip leading edge lands: tan(sweep) × half-span, minus a quarter of the taper. It is not the quarter-chord or the leading-edge sweep; the real angles it produces are under Derived Parameters. | deg |
| Dihedral | Angle of the tip above the root, -20 to 30°; negative is anhedral, the tips below the root. Sets the end of the front-view curve; points on that curve shape the path between. | deg |
| Tip twist | Geometric angle of the tip section relative to the root, -15 to 10°. Negative is washout: the tip flies at a lower angle and stalls after the root. The profile between is the twist curve. | deg |
| Bias | Where along the tip chord the rounded cap reaches furthest out, as a percentage from the leading edge, 5 to 95. Tangency to the edges limits the range; the readout says where the peak actually landed. | % chord |
| Reach | How far the cap extends past the tip station, as a percentage of half the tip chord: at 100 it reaches half a tip chord outboard; at 0 the tip is cut flat. The export carries the same cap. | % tip chord |
| Loft sections | How many stations the exporter lofts through between root and tip, 10 to 80, default 30. More follows a curved edge or a twist profile more closely and takes longer to build. |  |
| TE thickness | Opens every station's trailing edge to at least this, up to 10 mm, for a cutter or a printer that cannot make a knife edge. 0 keeps each section's own edge. The viewer always shows the section as drawn. | mm |
| Format | STEP is the exact lofted solid for CAD: shell it, split it, cut moulds from it. STL is the same solid as a triangle mesh for slicers and mesh tools. Both are in millimetres and hold both halves. |  |
| Generate 3D wing | Builds the solid in CAD on the server and downloads it, usually in under 20 s; it stops at 90 s and says why. Needs a sign-in and a root section. The file is the same loft the viewer shows. |  |
| 3D preview | The wing lofted live from the controls, both halves. Seven camera views on keys 1–7, Ortho or Persp on O, the ground grid on G, Expand on E. Drag to orbit, scroll to zoom, right-drag to pan. |  |
| Shading | Solid shows the surface as a painted composite would read. Solid+wire adds the station rings and the leading, trailing and quarter-chord lines over it. Wires shows only those, so the loft is visible through the wing. |  |
| Tail area | Stabiliser planform area, both sides together, in m². With the arm it sets the tail volume V_H; the cm² echo under the inputs is for foil builders, who size in cm². | m² |
| Tail arm | From the wing's quarter chord at its MAC to the stabiliser's quarter chord at its MAC, in mm. On a hydrofoil it is roughly the fuselage length. | mm |
| Tail AR | Stabiliser aspect ratio, span² over area. It sets how much lift the tail makes per degree. 3–5 is the band the card calls responsive without stalling before the wing. |  |
| CG | Centre of gravity as a fraction of the wing MAC, measured aft of the MAC leading edge. 0.25 is the wing's own aerodynamic centre; the static margin is how far the neutral point sits behind this. | × MAC |
| Tail volume | V_H = S_h · l_h / (S · MAC): the tail's area times its arm, scaled by the wing's. The one number that says how much authority the tail has; the card shows where it sits among the site's rigs. |  |
| Neutral point | Stick-fixed neutral point of wing plus tail, as a fraction of MAC and in mm: the CG position at which the rig would be neutrally stable. No fuselage; one moves it forward by about 0.05–0.10 MAC. |  |
| Static margin | Neutral point minus CG, as a percentage of MAC. Positive is statically stable: a nose-up disturbance makes a nose-down moment. Larger is steadier and needs more stabiliser trim to fly level. | % MAC |
| Estimate terms | The four factors the neutral point is built from: area ratio S_h/S, arm in chords l_h/MAC, the tail's lift slope over the wing's, and 1 − dε/dα, how much of the wing's downwash the tail sits in. |  |
