# Ncrit

Ncrit sets how readily the boundary layer on a section is taken to turn turbulent. Every polar on this site is computed at three values, 1, 4, 9, and the charts default to 9.

## What it is

NeuralFoil, like XFoil before it, decides where laminar flow becomes turbulent with the e^N method: small disturbances in the boundary layer grow downstream, and transition is declared where their amplification reaches e^N. Ncrit is that N.

- A **high** Ncrit means disturbances must grow a lot before transition, so laminar flow runs further along the chord. That is a quiet freestream and a smooth surface.
- A **low** Ncrit means transition comes early. That is a rough or dirty surface, a turbulent inflow, or vibration.

It is a property of the flow and the surface, not of the section. The same section at the same Reynolds number gives a different polar at each Ncrit, which is why the stored sweep carries all three.

## Which value to use

- **9** is the conventional value for a clean wind tunnel and the standard for comparing sections. It is the default on every chart here and the value every summary figure (max Cl, best L/D, min Cd) is read at. Use it unless you have a reason not to.
- **4** stands for a rougher surface or a more turbulent flow: a painted wing with some texture, a propeller wash, water with some chop.
- **1** is the pessimistic case: transition almost at the leading edge. Useful as a lower bound, or for a surface you know is rough.

The XFoil manual gives ranges for named conditions: a sailplane in still air 12–14, a motor glider 11–13, a clean tunnel 10–12, an average tunnel 9, a dirty tunnel 4–8. The three stored values bracket the cases that matter for most builds; a live run on the foil page uses whichever Ncrit the chart is set to.

## What changing it moves

Mostly the drag bucket, not the lift curve. Earlier transition thickens the turbulent boundary layer, which raises skin friction and narrows the low-drag range; the lift-curve slope and the zero-lift angle barely move. At low Reynolds numbers (below a few hundred thousand) the picture is less tidy, because a laminar separation bubble can be shortened by earlier transition and the drag may go **down** when Ncrit goes down.

The stored sweep shows both effects. These are measured from the polars on this site, not a rule of thumb:

**naca2412: what Ncrit changes, by Reynolds number**

| Re | CD min · Ncrit 1 | Ncrit 4 | Ncrit 9 | (L/D) max · Ncrit 1 | Ncrit 4 | Ncrit 9 |
| --- | --- | --- | --- | --- | --- | --- |
| 100k | 0.0145 | 0.0132 | 0.0159 | 42 | 48 | 50 |
| 200k | 0.0120 | 0.0096 | 0.0100 | 52 | 61 | 67 |
| 500k | 0.0101 | 0.0077 | 0.0064 | 68 | 75 | 88 |
| 1M | 0.0091 | 0.0071 | 0.0055 | 81 | 85 | 100 |

Source: Stored NeuralFoil polars for naca2412 (https://foil.tools/api/polars/naca2412), read 2026-11-05; minimum CD and best L/D over α -5° to 15°.

**sd7037: what Ncrit changes, by Reynolds number**

| Re | CD min · Ncrit 1 | Ncrit 4 | Ncrit 9 | (L/D) max · Ncrit 1 | Ncrit 4 | Ncrit 9 |
| --- | --- | --- | --- | --- | --- | --- |
| 100k | 0.0133 | 0.0123 | 0.0153 | 49 | 55 | 55 |
| 200k | 0.0113 | 0.0088 | 0.0091 | 62 | 69 | 75 |
| 500k | 0.0098 | 0.0071 | 0.0058 | 78 | 87 | 99 |
| 1M | 0.0089 | 0.0067 | 0.0049 | 89 | 102 | 115 |

Source: Stored NeuralFoil polars for sd7037 (https://foil.tools/api/polars/sd7037), read 2026-11-05; minimum CD and best L/D over α -5° to 15°.

Read a row left to right. At 100k the NACA 2412 has **less** minimum drag at Ncrit 4 than at 9, because the earlier transition shortens its separation bubble; by 500k the order has flipped and Ncrit 9 is cleanest, as the textbook says. The SD7037, a low-Reynolds section designed to avoid the bubble, behaves more evenly. The lesson for a builder: at a low Reynolds number, test the Ncrit that matches your surface rather than assuming 9 is the optimistic case.

## Where to set it

- **Foil page:** the Ncrit dropdown above the chart. It filters the stored polars and is sent with a live run.
- **Compare:** the Ncrit select in the analysis options; library sections keep their stored polars at the chosen Ncrit.
- **Mission:** "Turbulence (Ncrit)", which the selector passes to the polar lookup.
- **Optimize:** under Advanced.

![The left column below the simulation conditions: the Plot type menu, the Ncrit menu set to 9, and the Reynolds numbers menu with 3 selected, each ringed.](https://media.foil.tools/docs/shots/foil-page-chart-controls.9d29a2009c7a.webp)

*Three menus in the left column set what the chart draws.*

![The Environment card on Mission with Water (Salt - ITTC 3.5%) chosen, ρ 1025.90 kg/m³ and μ 1220.0 μPa·s shown, and Ncrit 9.0 (Smooth). The fluid menu and the Ncrit menu are ringed.](https://media.foil.tools/docs/shots/mission-fluid.5744f6635445.webp)

*Environment: the fluid sets density and viscosity, shown beside it; Ncrit is the transition setting the search reads the stored polars at.*

**Recording: Switching Ncrit on the foil page** (42 s, https://media.foil.tools/docs/ncrit-switch.93fea8d588ad.mp4)

> Every section is stored at Ncrit 1, 4 and 9. The chart opens at 9, the clean-tunnel standard.
> Ncrit 1 puts transition almost at the leading edge: the drag bucket narrows and the lift curve barely moves.
> Ncrit 4 stands for a rougher surface or a more turbulent flow, between the two.
> Back to 9. Pick the level that matches your surface and your air or water; choppy water reads the Ncrit 4 curve.
