# Mission and results

Mission is the first question of a design: how big, how fast, in what, carrying what? You type the surface, the fluid and the conditions it must serve, and the page turns each condition into the two numbers a section is judged by, a Reynolds number and a lift coefficient. Search Database then ranks the library against those points and hands you a shortlist on `/results`. Nothing here optimises a shape; it chooses among sections already analysed.

## What Mission computes

### The surface

**Mass** is the load this one surface carries, not the vehicle's total: lift L = m × 9.81 m/s². For a main wing that is the whole craft. A stabiliser carries a different, often downward, trim load; enter that on a Constraint point in newtons and leave Mass alone. **Wing Area** S and **Wingspan** b give the mean chord c = S / b, shown as **MAC** in mm, and the aspect ratio b² / S, shown as **AR**. Nothing on this page uses AR; the [wing pages](/docs#wings) do.

![The Vehicle Definition card on Mission filled for the freeride foil: mass 95 kg, wing area 0.1 m², wingspan 1 m, with the derived AR 10.00 and MAC 100.0 mm. Mass, wing area and the AR and MAC readouts are ringed.](https://media.foil.tools/docs/shots/mission-surface.788235239d14.webp)

*Vehicle Definition: the load, the area and the span. AR and the mean chord are worked out from them.*

### The fluid

**Fluid Type** sets density ρ and dynamic viscosity μ: air at sea level 1.225 kg/m³ and 18 μPa·s; fresh water 999.1 kg/m³ and 1139 μPa·s; salt water 1025.9 kg/m³ and 1220 μPa·s (ITTC values at 15 °C). The pair in use is printed beside the selector. **Air (custom altitude)** scales density as 1.225 × e^(−h / 8500), h in metres, and keeps sea-level viscosity. **Turbulence (Ncrit)** picks which of the three stored polar sets the search reads; [Ncrit](/docs/ncrit) explains the choice.

![The Environment card on Mission with Water (Salt - ITTC 3.5%) chosen, ρ 1025.90 kg/m³ and μ 1220.0 μPa·s shown, and Ncrit 9.0 (Smooth). The fluid menu and the Ncrit menu are ringed.](https://media.foil.tools/docs/shots/mission-fluid.5744f6635445.webp)

*Environment: the fluid sets density and viscosity, shown beside it; Ncrit is the transition setting the search reads the stored polars at.*

### Operating points

Each row of the Flight Envelope card is one condition, typed as a speed in the unit chosen at the top right. For each, with V in m/s:

- Re = ρ × V × c / μ, on the mean chord
- CL = L / (½ × ρ × V² × S), with L from Mass or from the point's own load

**Kind** says what the point is for. A **performance** point is scored: the section's drag at that CL and Re goes into the ranking, multiplied by the point's **weight** share (weights are normalised across the performance points). A **constraint** point is checked, never scored. Add a row for every condition the section must serve; the × removes one.

**Recording: Typing the job into Mission** (62 s, https://media.foil.tools/docs/mission-operating-points.6986837e6857.mp4)

> Mass is the load this surface carries: rider, board and rig, 95 kg for the freeride foil.
> Area and span give the mean chord, and the chord with the speed gives the Reynolds number.
> Salt water puts the same chord and speed at about fifteen times the Reynolds number of air.
> Two operating points: cruise at 7 m/s scores the section; take-off at 4 m/s is a constraint it must not stall at.
> A thickness filter of 10 to 14 % keeps sections thick enough for a carbon spar.
> Search Database works out the Reynolds number and lift coefficient at each point and ranks the library against them: Re 590k and CL 0.37 at cruise, CL 1.14 at take-off.

## Two worked rows

| | Freeride wing foil | RC trainer |
|---|---|---|
| Mass, area, span | 95 kg, 0.10 m², 1.0 m | 2.5 kg, 0.35 m², 1.4 m |
| Fluid | salt water | air at sea level |
| Mean chord, AR | 100 mm, 10 | 250 mm, 5.6 |
| Cruise (performance) | 7 m/s: Re ≈ 590,000, CL ≈ 0.37 | 15 m/s: Re ≈ 255,000, CL ≈ 0.51 |
| Take-off (constraint) | 4 m/s: Re ≈ 336,000, CL ≈ 1.14 | — |

These are the numbers the page's own constants give, and what the search runs against. The cruise point is what you type into the foil page's live run; take-off is a load the section must carry, not a condition it is scored at.

## Performance and constraint points

A performance point asks "how much drag at this CL?" and the answer is scored. A constraint point asks "can the section carry this at all?": the search reads the section's pre-stall lift peak (Clmax) at the point's own Reynolds number and requires the point's CL to be no more than 90% of it, Gudmundsson's wing-versus-section margin; a downward load, typed as negative newtons, is checked against the negative stall instead. A section that fails is dropped and named above the results. A constraint point carries no weight, adds nothing to Suitability or the matrix, and the Cm filter is not applied at it. The foil's take-off row is the typical use: CL 1.14 at Re 336,000 needs a Clmax there of about 1.27 or more.

![The Flight Envelope card on Mission: a performance point at 7 m/s with weight 5 and a constraint point at 4 m/s, the speed unit menu, the Kind menus and the Add Operating Point button ringed.](https://media.foil.tools/docs/shots/mission-op-points.444e58db02ba.webp)

*Flight Envelope: one row per operating point, in the speed unit at the top right. Kind says whether the point is scored or must only be carried.*

## Filters

Three optional filters narrow the library before anything is scored. **Thickness** and **Camber** are read from the section's geometry (maximum values as a percentage of chord, camber by its magnitude) and are hard limits: structure is a requirement, not a preference. **Pitch Moment (Cm)** is tested at each performance point's matched angle, so a band means at the conditions you fly, not anywhere on the polar.

![The Optional Filters card on Mission with the Thickness filter ticked, 10 to 14 percent, ringed; Pitch Moment and Camber are unticked.](https://media.foil.tools/docs/shots/mission-filters.e83e644c6853.webp)

*Optional Filters: tick one and set its range. The section is dropped before scoring if it falls outside.*

## Criteria weights and presets

By default the ranking is drag alone. The Selection Criteria card opens six sliders, 0 to 5, after Gudmundsson's decision matrix (§8.3.9):

![The Selection Criteria card open on Mission: the preset buttons and six weight sliders, drag at 1 and the other five at 0. The presets and the sliders are ringed.](https://media.foil.tools/docs/shots/mission-criteria.26cab2521232.webp)

*Selection Criteria, opened: a preset, or six sliders. Drag alone is the default.*

- **Drag**: CD at each operating CL, weighted by the operating points — the only criterion the default ranking uses. Lower is better.
- **Clmax**: pre-stall lift peak at the main operating Re. Higher is better.
- **Stall gentleness**: share of lift lost 3° past the peak; a gentle stall scores better than a higher, abrupt one. Lower is better.
- **Pitching moment**: mean |Cm| at the operating points; a large moment becomes trim drag. Lower is better.
- **Efficiency ratio**: Clmax divided by minimum CD at the main operating Re. Higher is better.
- **L/D placement**: degrees between the best-L/D angle and the main operating angle. Lower is better.

Each criterion is scaled 0–1 across the candidates that matched, multiplied by its weight and summed; the lowest total ranks first. **Drag only** is the default preset; **Textbook** is Gudmundsson's own weights (Drag 3, Clmax 2, Stall gentleness 3, Pitching moment 1, Efficiency ratio 1, L/D placement 1); any other mix shows as custom. The stall criterion reads the stored polar a few degrees past its lift peak; a polar that ends sooner is read as far as it goes, and the results page says so under the bars.

## Presets and the three actions

**Load Preset** fills every field from a saved set and **Save** stores the whole form under a name, in this browser and, when signed in, in your account. Three buttons leave the page: **Search Database** runs the selector and opens the results. **Apply to Wing →** carries the operating points, fluid, Ncrit, filters, mass and area to the [wing designer](/wing), which takes its speed, fluid and lift coefficient from the heaviest-weighted point and pre-fills a constant-lift analysis sweep from the mass; no search runs. **Optimize →** carries the same points, Ncrit and filters to [Optimize](/optimize), so a shape can be optimised at exactly these Re and CL.

![The row of buttons at the bottom of Mission: Load Preset and Save ringed together, Apply to Wing and Optimize ringed together, and Search Database ringed.](https://media.foil.tools/docs/shots/mission-actions.d6e44f94357e.webp)

*The buttons at the foot of the form: presets on the left, the three ways out on the right.*

## Results

**Recording: Reading the ranked results** (24 s, https://media.foil.tools/docs/mission-results.b34651ebfa6c.mp4)

> The take-off constraint point excluded every section that would stall at CL 1.14 and Re 340k.
> The rest are ranked at the cruise point. Suitability is the weighted score against the criteria, drag only by default; the SD 8040 leads with 10 % thickness.
> The Decision Matrix shows each criterion's weight; change the weights on Mission and the ranking changes with them.
> Compare top 5 takes the shortlist to Compare, where the candidates sit on one chart at your Reynolds number.

The results page runs the search and lists the best-ranked sections, each with its shape, the stored polars around its operating points (a star marks each matched Cl and Cd), a match table and the decision matrix. A line at the top names any section a constraint point rejected.

![The top of the results: the list of 166 sections excluded by a constraint point, ringed in orange, above the Top Recommended Airfoils header.](https://media.foil.tools/docs/shots/mission-results-excluded.1f342be99b96.webp)

*The results open on what the constraint point ruled out: every section that cannot reach the take-off lift at its Reynolds number.*

### Suitability

Suitability = 100 × e^(−10 × drag), where drag is each performance point's matched Cd times its weight share, summed; 100 would be zero drag. It is the drag-only ranking's own scale: with other criteria weighted the list is ordered by the matrix instead, and the header says so, but the percentage keeps its meaning.

![The first result card, sd8040, rank 1: Suitability 94.36 % with thickness 10.0 % and camber 2.6 %, ringed in orange, the airfoil shape, and the matched polars plot.](https://media.foil.tools/docs/shots/mission-results-card.dd4d91871a53.webp)

*One card per section, best first. Suitability is the drag-only score; the plot marks each operating point on the section's stored polars.*

### The match table

One row per operating point. **Match Re** is your exact value, interpolated between the two stored sweeps around it, or the nearest stored sweep outside the stored range. **Match Cl** is the required lift coefficient; a section that cannot reach it before stall at that Re is not in the list. **Match Cd**, **Match Cm** and **Alpha** are interpolated at that Cl on the pre-stall branch. **Score** is Match Cd × 1000, scaled to read at a glance; lower is better, and the weighted sum of these is the drag term behind Suitability.

![The Performance Data Table of the first result: one row per operating point with Match Re, Match Cl, Match Cd, Match Cm, alpha and score, ringed in orange.](https://media.foil.tools/docs/shots/mission-results-table.f6dbbd7ca57e.webp)

*The match table: what the section does at each operating point.*

### Decision matrix

Six bars, one per criterion: a full bar is the best of the candidate set, an empty one the worst, ×w the weight it was multiplied by. With weights other than the default the heading also shows the matrix score, 100 × (1 − weighted cost / Σ weights). The bars are shown for a drag-only search too, so a ranking explains itself.

![The Decision Matrix of the first result: six bars, drag, Clmax, stall gentleness, pitching moment, efficiency ratio and L/D placement, ringed in orange.](https://media.foil.tools/docs/shots/mission-results-matrix.74c9d4761aab.webp)

*The decision matrix: one bar per criterion, a full bar the best of the set.*

### From the shortlist

**Compare Top 5** opens the first five on [Compare](/docs/compare); **Export Top 5** downloads each as DAT or DXF (1000 mm chord), the files the [foil page](/docs/foil-page) offers; **Copy Summary** and **Copy Table** copy the ranking, or one section's rows, as a table. **Design Custom →** hands the points and the top-ranked section to [Optimize](/optimize) as its starting shape. Arriving from the wing designer's Find →, each card also carries **Apply →** for the slot you came from.

![The Top Recommended Airfoils header with Compare Top 5 ringed, and the Export Top 5 (.DAT), Export Top 5 (.DXF) and Copy Summary buttons ringed together.](https://media.foil.tools/docs/shots/mission-results-actions.f185160102d2.webp)

*Above the first card: take the shortlist to Compare, or download it.*

## What this hands on

Mission ends with operating points and a shortlist. The points, a Re and a CL per condition, are what you type into the foil page's live run and tick in its Reynolds list; the shortlist is what you take to [Search](/docs/search) and [Compare](/docs/compare) to settle on one section, then read in full on its [foil page](/docs/foil-page). Apply to Wing → carries the points to the [wing designer](/wing); Optimize → and Design Custom → carry them to [Optimize](/optimize).

## Controls on this page

| Control | What it does | Units |
| --- | --- | --- |
| Mass | The load this one surface carries, as a mass: lift = m × 9.81 m/s². For a main wing that is the whole craft. A stabiliser enters its trim load on a Constraint point in newtons instead, and can leave this blank. | kg or lb |
| Wing area | Planform area of this surface. With the load it gives the lift coefficient, CL = L / (q·S); with the span it gives the mean chord the Reynolds number is computed on. | m² or ft² |
| Wingspan | Tip-to-tip span. Area over span is the mean chord every operating point's Reynolds number is computed on; span squared over area is the aspect ratio shown beside it. | m or ft |
| AR | Aspect ratio, span squared over area, read-only. Nothing here uses it: the selector scores sections. It sets how much induced drag the finite wing adds, which the wing pages model. |  |
| MAC | Mean chord, area over span, in mm: the chord each operating point's Reynolds number is computed on. A tapered wing's mean aerodynamic chord differs a little; the wing designer works that one out. | mm |
| Fluid type | Density and viscosity for Re and dynamic pressure: air at sea level 1.225 kg/m³, fresh water 999.1, salt water 1025.9 kg/m³ (ITTC values at 15 °C). The ρ and μ in use are printed beside the selector. |  |
| Altitude | Only for "Air (custom altitude)": density falls as 1.225·e^(−h/8500) with h in metres, an isothermal-atmosphere fit; viscosity stays at sea-level air. Higher means a lower Re and a higher lift coefficient. | m or ft |
| Unit | The unit every speed on this card is typed in. Knots and km/h are converted to m/s before Re and CL are computed. Changing the unit does not convert the numbers already typed. |  |
| Speed | One condition the section must serve. Each row becomes an operating point: Re = ρ·V·c/μ on the mean chord and CL = L / (½ρV²·S) from the load. Add a row for cruise, top speed, take-off. |  |
| Kind | Performance: scored, its drag at the required CL goes into the ranking. Constraint: checked, the section must reach the point's load with a stall margin or it is excluded and named; it adds nothing to the score. |  |
| Weight | Relative importance of a performance point. Weights are normalised to shares across the performance points, and each point's matched drag is multiplied by its share. A constraint point has no weight. |  |
| Load | The load a constraint point must carry, in newtons; the kgf equivalent is shown beneath. Negative is a downward load, checked against the negative stall instead of Clmax. Blank falls back to Mass × g. | N |
| Pitch moment (Cm) | Keep only sections whose pitching moment about the quarter chord, at each performance point's matched angle, lies between Min and Max. Checked at the points you fly, not the polar's extremes; not applied at constraint points. |  |
| Thickness | Keep only sections whose maximum thickness, as a percentage of chord, lies between Min and Max. A hard filter applied before any scoring: structure is a requirement, not a preference. | % chord |
| Camber | Keep only sections whose maximum camber, as a percentage of chord, lies between Min and Max. The magnitude is tested, so a reflexed or inverted section counts by its size. Applied before scoring. | % chord |
| Preset | Drag only ranks by the matched drag alone, the default. Textbook is Gudmundsson's worked example: Drag 3, Clmax 2, Stall gentleness 3, Pitching moment 1, Efficiency ratio 1, L/D placement 1. Any other mix shows as custom. |  |
| Drag | CD at each operating CL, weighted by the operating points — the only criterion the default ranking uses. Lower is better: scaled 0–1 across the matched candidates and multiplied by this weight. |  |
| Clmax | Pre-stall lift peak at the main operating Re. Higher is better: scaled 0–1 across the matched candidates and multiplied by this weight. |  |
| Stall gentleness | Share of lift lost 3° past the peak; a gentle stall scores better than a higher, abrupt one. Lower is better: scaled 0–1 across the matched candidates and multiplied by this weight. |  |
| Pitching moment | Mean \|Cm\| at the operating points; a large moment becomes trim drag. Lower is better: scaled 0–1 across the matched candidates and multiplied by this weight. |  |
| Efficiency ratio | Clmax divided by minimum CD at the main operating Re. Higher is better: scaled 0–1 across the matched candidates and multiplied by this weight. |  |
| L/D placement | Degrees between the best-L/D angle and the main operating angle. Lower is better: scaled 0–1 across the matched candidates and multiplied by this weight. |  |
| Presets | Load fills every field from a saved set: surface, fluid, points, filters and weights. Save stores the form under a name. Presets live in this browser and, when signed in, in your account. |  |
| Apply to Wing → | Carries the operating points, fluid, Ncrit, filters, mass and area to the wing designer, which takes its speed, fluid and lift coefficient from the heaviest-weighted point. No search is run. |  |
| Optimize → | Carries the operating points, Ncrit and the filters to Optimize, so a shape can be optimised at exactly these Re and CL. No search is run first; Design Custom on the results page also starts from the top section. |  |
| Search Database | Runs the selector: every library section with a stored polar at this Ncrit, filtered by thickness and camber, matched at each point's Re and CL on the pre-stall branch, checked at the constraints, ranked by the weights. |  |
| Suitability | 100·e^(−10·drag), where drag is each performance point's matched Cd times its weight share, summed. 100 would be zero drag. It is the drag-only scale and does not change when other criteria are weighted. | % |
| Performance (matched polars) | The stored Cl–Cd polars at the Reynolds buckets around each operating point, at the chosen Ncrit, with a star at each point's matched Cl and Cd. A star near the bottom of a curve is a point flown in the drag bucket. |  |
| Match Re | The Reynolds number the row was read at: your exact value, interpolated between the two stored sweeps around it, or the nearest stored sweep when the point lies outside the stored range. |  |
| Match Cl | The lift coefficient the point requires, L / (½ρV²·S), which the section's polar was read at. A section that cannot reach it before stall at that Re is not in the list. |  |
| Match Cd | The section's drag coefficient at that Cl and Re, interpolated on the pre-stall branch of the stored polar. The one number the default ranking is built from. |  |
| Match Cm | Pitching-moment coefficient about the quarter chord at the matched angle; negative is nose-down. The value the Cm filter tests, and what the pitching-moment criterion averages. |  |
| Alpha | The angle of attack at which the section makes the required Cl at that Re, read off the stored lift curve. A wide spread between rows means the wing must work across a wide angle range. | deg |
| Score | Match Cd × 1000, the per-point term the drag sum is built from, scaled so it reads at a glance. Lower is better. Multiply by the point's weight share and sum to get the drag term behind Suitability. |  |
| Decision matrix | Where this section stood on each criterion among the candidates that matched: a full bar is the best of the set, empty the worst, ×w the weight. With non-default weights the matrix score is 100 × (1 − weighted cost / Σ weights). |  |
| Top recommended airfoils | Design Custom hands the points and the top section to Optimize; Compare Top 5 overlays the first five; Export Top 5 downloads each as DAT or DXF (1000 mm chord); Copy Summary copies rank, name, suitability, thickness and camber. |  |
