# Getting started

A design on foil.tools runs through eight stages: say what the job is, choose a section, read it at your Reynolds number, shape it if you must, build the wing, analyse it, balance the aircraft, and make the files the shop needs. Each stage hands something to the next, and two of them can send you back. This page is one pass through all eight with the free tools, on one worked example, with a link to the page that explains each stage.

**Figure: The design loop**

1. The job: mass, speed, area, span and fluid on Mission give the operating points
2. The section: Results, Search and Compare narrow the library to one name
3. Read it: the foil page at your Reynolds number and Ncrit
4. Shape it (optional): Optimize at the operating points, or edit on the Kulfan canvas
5. The wing: planform, sections along the span, twist and dihedral
6. Analyse: lift, drag and the first stall of the whole wing
7. Balance: the wing and a stabiliser about the centre of gravity, on Trim
8. Make it: STEP or STL of the wing, DXF or DAT of a section

Not enough lift, or too much drag? Analysis sends you back to the section; trim sends you back to the wing.

**Recording: The design loop: eight stages on one wing** (153 s, https://media.foil.tools/docs/design-loop.c31e722c4276.mp4)

> Mission takes the job: 95 kg on a 0.10 m² wing of 1 m span, in salt water, cruising at 7 m/s and taking off at 4 m/s.
> Search Database works out the Reynolds number and lift coefficient at each point, Re 590k and CL 0.37 at cruise, and ranks the library against them.
> Compare puts the shortlist and the NACA 63-412 the template carries on one chart at the stored Reynolds number nearest cruise.
> The section page has the stored sweep; type the exact Reynolds number and NeuralFoil runs it now. Max CL about 1.4 clears the take-off need of 1.14.
> The freeride reference design puts the section on a 1 m planform with 2° of washout; the viewer draws the loft the export will write.
> Wing analysis runs the whole wing: AeroBuildup in seconds, with the lift-to-drag ratio and where it stalls first.
> Wing analysis runs the whole wing in seconds. The cruise is good, but the Checks card says the tip stalls first: more washout or a different tip section, back at stage 5.
> Trim puts the wing and a stabiliser about the rider's centre of gravity and solves both together.
> Export writes the same loft as STEP for CAD or STL for printing; a section's DXF and DAT come from its page.
> Most of design is the arrow back: analysis sends you to the section, trim sends you to the wing, and you go round again.

## The worked example

A freeride wing foil, the site's own `Wing Foil — Freeride` reference design: rider, board and rig 95 kg, cruising at 7 m/s in salt water, taking off at 4 m/s; a 1 m span front wing of about 0.10 m² with a 145 mm root chord and a 62 mm tip, on the NACA 63-412. The same numbers appear on every page in this guide, so what one stage hands on is what the next one starts from.

## 1. The job

*How big, how fast, in what, carrying what?* [Mission](/input) takes mass, wing area, span, fluid and the speeds you must fly at, and turns them into operating points: for the freeride foil, a Reynolds number of about 590,000 and a lift coefficient of about 0.37 at cruise, and a lift coefficient of about 1.14 at take-off, which the section must reach without stalling. Search Database then ranks the library against those points. [Mission and results](/docs/mission) explains every field, the two kinds of operating point, and the score.

![The Flight Envelope card on Mission: a performance point at 7 m/s with weight 5 and a constraint point at 4 m/s, the speed unit menu, the Kind menus and the Add Operating Point button ringed.](https://media.foil.tools/docs/shots/mission-op-points.444e58db02ba.webp)

*Flight Envelope: one row per operating point, in the speed unit at the top right. Kind says whether the point is scored or must only be carried.*

**Hands on:** the operating points, and a ranked shortlist.

## 2. The section

*Which section does that job best?* [Results](/results) is the shortlist; [Compare](/foil/compare) puts the top few on one chart at your Reynolds number so you can read drag at the cruise lift coefficient; [Search](/search) is the way in when you know the family or the figures rather than the job. The example keeps the NACA 63-412 the template carries, because it holds the thickness a carbon layup wants. [Search](/docs/search) and [Compare](/docs/compare) explain the filters and the chart.

![The Performance Metrics card on Compare with its Plot type, Ncrit and Reynolds numbers menus ringed above the chart.](https://media.foil.tools/docs/shots/compare-chart-controls.3ced146a96d6.webp)

*The three menus above the chart: what is plotted, at which Ncrit, and which stored Reynolds numbers.*

**Hands on:** one section's name.

## 3. Read it

*What does it do at my Reynolds number and my Ncrit?* Every section has a page at `/foil/<name>`. Load the stored sweep, tick the Reynolds numbers around yours, and type the exact value under "Run it at your Reynolds number" for a live NeuralFoil polar. The At a glance table reads off the stall peak, the best lift-to-drag ratio and the minimum drag: a maximum lift coefficient of about 1.4 clears the take-off need of 1.14. [The foil page](/docs/foil-page) explains each control, [Reynolds number](/docs/reynolds-number) the sum, and [Ncrit](/docs/ncrit) the transition setting, which matters in choppy water.

![The Run it at your Reynolds number panel under the chart, with 590k typed in the box, the Run NeuralFoil button, and the free-runs counter ringed.](https://media.foil.tools/docs/shots/foil-page-live-re.5dff5a2eae79.webp)

*Under the chart: type your Reynolds number and press Run NeuralFoil. The counter says how many free runs you have left, or the hourly limit when you are signed in.*

**Hands on:** a verdict on the section, and its downloads if you need them now.

## 4. Shape it, if you must

*Can the section be better at exactly these points?* [Optimize](/optimize) starts from the section you read and reshapes it against the operating points under thickness and camber bounds; the [Kulfan canvas](/kulfan-canvas) edits a section by its CST weights, fits a `.dat` of your own, and exports it at any chord. Most designs skip this stage. [Optimize](/docs/optimize) and [Kulfan canvas](/docs/kulfan-canvas) explain the controls and why a run can return nothing.

![The Starting Airfoil card on Optimize with n63412 chosen, ringed, and its three readouts, thickness 11.99 %, camber 2.21 % and trailing edge 0.00 %, ringed in orange.](https://media.foil.tools/docs/shots/optimize-start.16145bea8926.webp)

*The starting section is the first card. Type a library name and pick it from the list; the readouts under it change to the start's own figures.*

**Hands on:** an improved or edited section, saved to your account or exported.

## 5. The wing

*What planform, which sections where, how much twist?* "Build a wing on it", on the section page, opens the [wing designer](/wing) with that section at root and tip; the Reference Designs panel loads the freeride foil in one click. Set half-span, chords and sweep ([Planform](/docs/wing-planform)), pick the root and tip sections ([Sections along the span](/docs/wing-sections)), and set washout, dihedral and the tip cap ([Twist, dihedral and the tip](/docs/wing-twist-dihedral)). The viewer draws the loft the export will write.

![The Reference Designs panel open on its watersports hydrofoils row, with the Wing Foil — Freeride card ringed: 1.00 m span, 1141 cm², aspect ratio 8.8, NACA 63-412.](https://media.foil.tools/docs/shots/wing-reference-designs.09730182c358.webp)

*Reference Designs, open. The freeride wing foil is the worked example these docs use; a click replaces the whole design with it.*

**Hands on:** a saved wing design.

## 6. Analyse

*Does the wing make the lift at take-off, and what does it cost at cruise?* [Wing analysis](/wing/analyze) runs the wing in 3D: AeroBuildup in seconds, or a vortex-lattice run for a more careful answer, in an angle sweep or at constant lift. It reports lift, drag, lift-to-drag ratio, span efficiency and where the wing stalls first. It is metered: a monthly free allowance, then credits. [Wing analysis](/docs/wing-analysis) explains the methods and the readout.

The freeride wing shows why this stage exists. Its cruise is good, a lift-to-drag ratio near 30 at 7 m/s, but the Checks card under the results marks it **FAIL**: it stalls tip-first, at 72 % of the span, and a wing that stalls at the tip drops a wing when it stalls. The card names the fix: more washout, or a tip section with more maximum lift.

![The Checks card under the results with its first row, FAIL: stall starts at 72 % span, tip-first, ringed in orange.](https://media.foil.tools/docs/shots/wing-analysis-checks.b8365b28d261.webp)

*Checks, under the results. The freeride wing as drawn fails the first one: it stalls tip-first, and the row names the fix.*

**Hands on:** the wing's numbers, or the arrow back: a tip-first stall means more washout or a different tip section (stage 5); not enough lift at 4 m/s means a different section (stage 2) or more wing (stage 5).

## 7. Balance

*Does the rig fly level with the rider where the rider is?* [Trim](/trim) puts the wing and a stabiliser about a centre of gravity and solves both together: trim angle, stabiliser setting, the load on each surface, the static margin and the thrust required. The hydrofoil template carries the freeride foil's rig. It is a paid tool. [Trim](/docs/trim) explains the inputs and the outputs.

![The Trim results after the sweep: the trim angle and stabiliser incidence, the load on each surface, the static margin and the required thrust, ringed in orange.](https://media.foil.tools/docs/shots/trim-outputs.140740230441.webp)

*The outputs, in the Trim card: the angle and stabiliser setting that fly level, the load each surface carries, the static margin and the thrust it takes.*

**Hands on:** a balanced rig, or the arrow back to the wing.

## 8. Make it

*What file does the shop need?* The designer exports the wing as STEP for CAD or STL for printing, sign-in required; a section page exports DXF for CAD, DAT for XFLR5 or OpenVSP, and CSV of the polars. [Export](/docs/wing-export) says what the file holds compared with the viewer, and [File formats](/docs/file-formats) says what each file contains and how it is scaled.

![The Generate 3D Wing card at the bottom of the designer with the Loft sections, TE thickness and Format inputs ringed as one row, and the Generate button ringed.](https://media.foil.tools/docs/shots/wing-generate.0751a562fa2c.webp)

*Export is the last card on the page: three settings, then Generate. The button needs you signed in.*

## After the first pass

- **Save your work.** Signed in, sections, wing designs and wing analyses save to the [dashboard](/dashboard) and reload from there.
- **Let an assistant drive.** Claude, ChatGPT, Grok and Claude Code can run every one of these stages against your account through the [connectors](/connectors); [Connect your agent](/docs/connect-your-agent) is the setup, and [MCP tools](/docs/mcp-tools) lists what they can call.
- **Coming from another tool?** [Coming from XFLR5, Flow5 or OpenVSP](/docs/from-xflr5-openvsp) maps their inputs onto these pages.
- **Not sure which page you need?** [Which tool?](/docs/which-tool) goes from the question to the page.
